Issue Adding a TMDI Card getting "Input out of range" for DLOP

[viper222]

OK, Below is my Config, I printed it all out just in case I was missing something. I am trying to add a third PRI and I currently have the card in the slot for loop 28. I have a Univ Trk card working in that cabinet as the only other card, it is functioning fine in Slot 21 so I know it is a working cabinet. Basically when I try to add the T-1 in LD 17 I get a SCH0582 which says "input out of range" I also posted my attempt at that below the CFN printout. So what am I missing? I figure it is probably something stupid. I tried the card for Loop 22 as well, just to test, but no luck there either. Thank you for any help ahead of time.

REQ PRT
TYPE CFN

ADAN HIST
SIZE 63000
USER TRF SCH BUG
ADAN TTY 0
TTY_TYPE SDI
CAB 00
CARD 00
PORT 0
DES
FLOW NO
USER MTC SCH CTY BUG
TTYLOG 0
BANR NO
ADAN TTY 1
TTY_TYPE SDI
CAB 00
CARD 00
PORT 1
DES MODEM
BPS 9600
BITL 8
STOP 1
PARY NONE
FLOW YES
BCST NO
USER MTC SCH BUG
TTYLOG 0
BANR NO
ADAN TTY 2
TTY_TYPE SDI
CAB 00
CARD 00
PORT 2
DES
BPS 9600
BITL 8
STOP 1
PARY NONE
FLOW NO
USER MTC SCH
TTYLOG 0
BANR YES
ADAN TTY 8
TTY_TYPE LSL
CAB 00
CARD 10
PORT 0
DES
BPS 1200
BITL 8
STOP 1
PARY NONE
FLOWTYPE MAIL
ADAN AML 9
CARD 10
PORT 1
DES
BPS 4800
CLOK EXT
IADR 003
RADR 001
T1 10
T2 002
T3 040
N1 128
N2 08
K 7
RXMT 05
CRC 10
ORUR 005
ABOR 005
ENL YES
ADAN ELAN 16
CTYP ELAN
DES CALLPILOT
N1 512
ADAN DCH 10
CTYP TMDI
CARD 08
PORT 1
DES PRI8
USR PRI
DCHL 8
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
RCAP COLP
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSRV NO
ADAN DCH 11
CTYP TMDI
CARD 07
PORT 1
DES PRI7
USR PRI
DCHL 7
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
RCAP COLP
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSRV NO
PARM
LPIB 150
HPIB 150
500B 16
NCR 364
MGCR 25
CSQI 64
CSQO 64
TUBO NO
CFWS YES
PCML MU
ALRM YES
ERRM ERR BUG AUD
DTRB 100
TMRK 128
FCDR OLD
PCDR NO
TPO NO
TSO NO
CLID NO
DUR5 NO
MLDN YES
MARP YES
FRPT NEFR
DCUS NULL
MSCL 255
PMSI
MANU PMS1
PMCR 20
PORT NONE
NDIS 20
OCAC NO
MTRO MR
SBA_ADM_INS 001
SBA_USER 010
BCAP SPEECH
IDLE_SET_DISPLAY NORTEL
CLNP YES
ICON YES
CEQU
MPED 8D
SUPL 000 004 008 012
016 032 036 040
044 048 064 068
072
XCT 000
CONF 029 030 031 062
094 095

DLOP NUM DCH FRM TMDI LCMT YALM T1TE TRSH
PRI 07 24 ESF YES B8S FDL 0 00
08 24 ESF YES B8S FDL 0 00
MISP
OVLY
SID 0
BKGD 044
PBXH 01
TODR 01
DROL 034 038 043 044 135
MULTI_USER ON
VAS
VSID 09
DLOP
AML 09
SECU NO
INTL 0001
MCNT 9999
CONF DIR
VSID 16
DLOP
ELAN 16
SECU NO
INTL 0001
MCNT 9999

ATRN
CODE 0
SOLR 12
ROLR +45.00
AOLR +45.00
TOLR -45.00
AGCD NO
VOLR NO
HRLR +42.00
HTLR -44.00

My Attempt:

>LD 17
CFN000
MEM AVAIL: (U/P): 774181 USED U P: 235598 169868 TOT: 1179647
DISK RECS AVAIL: 274
DCH AVAIL: 80 USED: 0 TOT: 80
TMDI D-CHANNELS AVAIL: 62 USED: 2 TOT: 64
AML AVAIL: 14 USED: 2 TOT: 16
REQ CHG
TYPE CEQU
TDS
CONF
DLOP 28
SCH0582

 

[yyrkroon]

DTI/PRI can only go in the first cabinet, slot 1-9; unless you have surviable expansion cabinets.

You'll know if you have surviable expansion cabinets if each of your expansion also has a SSC card.

 

[acewarlock]

Move a card out of the 1st Cab and put the DTI there.

 

[johnpoole]

glad i was right on that one.. i would move card 3 and add the tmdi there

john poole
bellsouth business
columbia,sc

 

[viper222]

Thanks all, I am moving that as we speak. Man, I guess I didn't ever see that, and of course, never told. It is sometimes the smallest things. Thank you so much again.

 

[worldwidedialtone]

While looking, are you running both Meridian Mail and Call Pilot? May want to get rid of your VSID 9 and AML 9 and tty 8.

MIKE

 

[viper222]

worldwidedialtone,

Nope, we are just running Call Pilot, very good eye, This is just the first time we have been to this site. THey are getting CSA0001 9 errors, so I haven't even looked into that. So basically, Call Pilot doesn't need an AML link so I can just remove it from a ADAN entry?? I just need the TTY 8 LSL type link?? If that is correct, I will do it. Thanks, I will wait for a confirmation on that though,

FYI that was it on the TMDI Card

 

[yyrkroon]

you can remove both tty 8 and aml 9 if you're using CP

 

[viper222]

Thank you guys Sooooo much.