Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Is 9630G supported on 406 v2
- Thread starter jslewis
- Start date
amriddle01
Programmer
Indeed, take your ACSS and it's one of the questions, actually I think they asked it twice 
ACSS (SME)
APSS (SME)
"I'm just off to Hartlepool to buy some exploding trousers
ACSS (SME)
APSS (SME)
"I'm just off to Hartlepool to buy some exploding trousers
hairlessupportmonkey
IS-IT--Management
or read the KB?
Telephone Support
• Avaya IP Endpoint Licenses
On IP500 and IP500v2 systems, Avaya 1600, 4600, 5600, 9600, IP DECT, DECT R4, T3 IP, Spectralink and VPN phones are licensed by Avaya IP Endpoint licenses. These licenses are consumed by each phone as it registers with the IP Office system. Existing VCM channel resources and VCM Channel licenses enable a number of unlicensed phone registrations.
• Additional Phones
The following additional phones are supported by IP Office Release 6.0.
• 1400 Series Phones
Using digital station ports, IP Office Release 6.0 supports the Avaya 1400 Series phones; 1403, 1408 and 1416. To the user they provide the same range of features are the equivalent 1600 Series phones on IP Office. Each 1416 can support up to 3 DBM32 buttons modules.
• 1600-I Series Phones
The 1600-I variants of the 1603, 1603SW, 1608 and 1616 phones are supported.
• 9600 Series Phones
The following Avaya H323 IP phones are supported: 9620L, 9620C, 9630G, 9640, 9640G, 9650 and 9650C. All except the 9620s can support up to 3 SMB24 button modules.
• These phones are supported by IP Office Release 6.0 on IP500 and IP500v2 systems only. The voice activated dialing and USB features are not supported.
Telephone Support
• Avaya IP Endpoint Licenses
On IP500 and IP500v2 systems, Avaya 1600, 4600, 5600, 9600, IP DECT, DECT R4, T3 IP, Spectralink and VPN phones are licensed by Avaya IP Endpoint licenses. These licenses are consumed by each phone as it registers with the IP Office system. Existing VCM channel resources and VCM Channel licenses enable a number of unlicensed phone registrations.
• Additional Phones
The following additional phones are supported by IP Office Release 6.0.
• 1400 Series Phones
Using digital station ports, IP Office Release 6.0 supports the Avaya 1400 Series phones; 1403, 1408 and 1416. To the user they provide the same range of features are the equivalent 1600 Series phones on IP Office. Each 1416 can support up to 3 DBM32 buttons modules.
• 1600-I Series Phones
The 1600-I variants of the 1603, 1603SW, 1608 and 1616 phones are supported.
• 9600 Series Phones
The following Avaya H323 IP phones are supported: 9620L, 9620C, 9630G, 9640, 9640G, 9650 and 9650C. All except the 9620s can support up to 3 SMB24 button modules.
• These phones are supported by IP Office Release 6.0 on IP500 and IP500v2 systems only. The voice activated dialing and USB features are not supported.
Jlewis,
I think 96xx phones are locked out on 406v2/412 with r6.
I did get 9630/9650 to work with r5.18 and r5.20 on a 406v2, using firmware 1.0/1.1, but You will not see caller Id until You p/u the phone.
Back in the Day I did get 96xx phones to work with r4.0 or was it r4.2, cant remeber, There was only one relase they were supported, right after the 17xx phones were ditched. They did work on both 406v2, and SOE! They were supported but only with firmware 1.5
Andre
I think 96xx phones are locked out on 406v2/412 with r6.
I did get 9630/9650 to work with r5.18 and r5.20 on a 406v2, using firmware 1.0/1.1, but You will not see caller Id until You p/u the phone.
Back in the Day I did get 96xx phones to work with r4.0 or was it r4.2, cant remeber, There was only one relase they were supported, right after the 17xx phones were ditched. They did work on both 406v2, and SOE! They were supported but only with firmware 1.5
Andre
- Status
