IPv4 alarms...

[98Converter]

I've got the following alarms in my switch... They don't appear to be service impacting, but curious if anyone else has seen these, and what steps they took to clear them.

01A1017 ETH-PT n IPv4 WARNING IN 03/12/09:57 00/00/00:00
01A1117 ETH-PT n IPv4 WARNING IN 03/12/09:58 00/00/00:00
01A1217 ETH-PT n IPv4 WARNING IN 03/12/09:59 00/00/00:00
01B1017 ETH-PT n IPv4 WARNING IN 03/12/10:00 00/00/00:00
01B1117 ETH-PT n IPv4 WARNING IN 03/12/10:01 00/00/00:00
01B1217 ETH-PT n IPv4 WARNING IN 03/12/10:01 00/00/00:00

Thanks,
98C

We are what we repeatedly do. Excellence, then, is not an act but a habit. ARISTOTLE 384-322 B.C.

 

[AvayaTier3]

What does the error log show for these alarms?

A great teacher, does not provide answers, but methods to teach others "How and where to find the answers"

bsh

36 years Bell, AT&T, Lucent, Avaya
Tier 3 for 26 years and counting

http://bshtele.com

 

[98Converter]

From the error log:

01A1017 ETH-PT IPv4 513 03/09/09:57 255 3 3 a y
03/12/13:28



Thanks,
98C

We are what we repeatedly do. Excellence, then, is not an act but a habit. ARISTOTLE 384-322 B.C.

 

[phoneguy55]

Error Type 513: Link Integrity Inquiry test (#1282) failed, or C-LAN port detected loss of
Ethernet link integrity.
Possible causes:
? Cables
? Ethernet transceiver
1. Test the port (test port location long).
2. If the Link Integrity Inquiry Test (#1282) fails, refer to its repair procedure.

Link Integrity Inquiry Test (#1282)
This nondestructive test queries the C-LAN Ethernet port’s physical connections.
Table 601: Link Integrity Inquiry Test (#1282) 1 of 2
Error
Code
Test
Result
Description / Recommendation
1124 ABORT Ethernet link is not enabled.
1. Verify that the Ethernet link is enabled (status port location,
status link n, or display data-module).
2. If the link is not enabled, enable the link (change data-module).
3. Repeat the test.
4. Escalate if the problem persists.
1125 ABORT Ethernet link not in service.
1. Verify whether Ethernet link is in service (status port location
or status link n).
2. If the Ethernet link is not in service, release the link (release link
n or release port location).
3. Repeat the test.
4. Escalate if the problem persists.
1959 ABORT Downlink message error.
1. Retry the command at 1-minute intervals, up to 3 times.
2. Escalate if the problem persists.
2012 ABORT Internal system error.
1. Retry the command at 1-minute intervals, up to 3 times.
2. Escalate if the problem persists.
2100 ABORT Could not locate the necessary system resources to run this test.
1. Retry the command at 1-minute intervals, up to 5 times.
2. Escalate if the problem persists.
2500 ABORT Internal system error.
1. Retry the command at 1-minute intervals, up to 3 times.
2. Escalate if the problem persists.
FAIL Link integrity lost due to problem with attachment of Ethernet cable to the
port.
1. Repeat the test.
2. If the test fails, verify that the cable properly is secured to Ethernet port
and to the bus.
3. Verify the C-LAN circuit pack’s link integrity LED is lit.
4. Retry the test.
5. If problem persists, see Ethernet Local Looparound Test (#1278)
repair procedures.
PASS The Ethernet Link Integrity test (#1282) passed