Hi All,
this is what I get,
1 Bootmgr
2 IPSO
Default: 1
Starting bootmgr
Loading boot manager..
Boot manager loaded.
Entering autoboot mode.
Type any character to enter command mode.
BOOTMGR[3]> help
boot Boot/Load and Run kernel or executable
install Proceed to install new IPSO image
halt Halt the system
setenv Set Environment Variable
unsetenv Clear Environment Variable
printenv Print Environment Variables
passwd Set password for system
ls List Directory
sysinfo Display System Information
unsetalias Clear System alias
setalias Set System alias
showalias Show System aliases
set-defaults Set bootmgr defaults
netconfig Configure network boot parameters
BOOTMGR[4]> ls
IPSO-3.7-BUILD026-08.19.2003-184000-1214
current
BOOTMGR[5]> set-defaults
BOOTMGR[6]> boot
Booting /dev/wd0f:/image/IPSO-3.7-BUILD026-08.19.2003-184000-1214/kernel
[kernel] symtab a06a6000, sym_start a06a6004, sym_end a06e7278
[kernel] sym_size 56df, str_size 5f5e4
[ preserving 0xa085c bytes of kernel symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Resizing packet buffers: mbufs 15360 clusters 14000
releng 1214 08.19.2003-184000
CPU: 300-MHz Pentium (586-class CPU)
real memory = 268435456 (256M bytes)
avail memory = 251539456 (239M bytes)
mediagx0 <Cyrix GXLV CPU with PCI/Memory Controller> rev 0 on pci0:0:0
mediagx1 <Cyrix CS5530 PCI to ISA bridge> rev 48 on pci0:18:0
mediagx2 <Cyrix CS5530 SMI> rev 0 on pci0:18:1
mediagx3 <Cyrix CS5530 IDE> rev 0 on pci0:18:2
cyrix 5530
Probing for devices on the ISA bus:
sio0 at 0x3f8-0x3ff irq 4 on isa
<5>sio0: type 16550A
sio1 at 0x2f8-0x2ff irq 3 on isa
<5>sio1: type 16550A
wdc0 at 0x1f0-0x1f7 irq 14 on isa
Setting using 0x1000
wd0: mw=0x2, pio=0x4, pcirev=0x0, udma=0x2
wdc0: unit 0 (wd0): <TOSHIBA MK2018GAS>, LBA, DMA
wd0: 20003MB (39070080 sectors), LBA geometry: 2432 cyls, 255 heads, 63 S/T
wd0: Physical geometry: 16383 cyls, 16 heads, 63 S/T
npx0 on motherboard
npx0: INT 16 interface
superio0 at 0x0 on isa
mediagx4 <Cyrix CS5530 audio> rev 0 on pci0:18:3
fxp0 <Intel EtherExpress Pro 10/100B Ethernet> rev 16 int a irq 6 slot 1
netlog:eth-s1p1 .. Ethernet address 0:a0:8e:21:dd:22
fxp1 <Intel EtherExpress Pro 10/100B Ethernet> rev 16 int a irq 10 slot 2
netlog:eth-s2p1 .. Ethernet address 0:a0:8e:21:dd:23
fxp2 <Intel EtherExpress Pro 10/100B Ethernet> rev 16 int a irq 11 slot 3
netlog:eth-s3p1 .. Ethernet address 0:a0:8e:21:dd:24
ubsec0 <Broadcom 5802 Encryption Accelerator> rev 1 int a irq 12 on pci0:13:0
sizeof hwa_dev_t = 12
changing root device to wd0f
swapon: adding /dev/wd0b as swap device
Automatic reboot in progress...
/dev/rwd0f: clean, 461247 free (831 frags, 57552 blocks, 0.1% fragmentation)
/dev/rwd0a: CLEAN FLAG NOT SET IN SUPERBLOCK (FIXED)
/dev/rwd0a: 4 files, 28 used, 37528 free (16 frags, 4689 blocks, 0.0% fragmentation)
/dev/rwd0d: CLEAN FLAG NOT SET IN SUPERBLOCK (FIXED)
/dev/rwd0d: 822 files, 884943 used, 13847992 free (816 frags, 1730897 blocks, 0.0% f)/dev/rwd0e: CLEAN FLAG NOT SET IN SUPERBLOCK (FIXED)
/dev/rwd0e: 4755 files, 625100 used, 1936096 free (2272 frags, 241728 blocks, 0.1% f)Apr 22 13:21:39 xpand[28]: xpand will perform upgrade if necessary
clearing /tmp
checking for core dump...savecore: no core dump
recording kernel -c changes
starting system daemons: syslogd done.
Apr 22 13:21:42 IZC1S100 [LOG_NOTICE] kernel: sio0: type 16550A
Apr 22 13:21:42 IZC1S100 [LOG_NOTICE] kernel: sio1: type 16550A
ifmnetlog:eth-s3p1 .. enabling 10baseT/UTP port in half duplex mode
netlog:eth-s2p1 .. enabling 100baseTX/UTP port in full duplex mode
netlog:eth-s1p1 .. enabling 100baseTX/UTP port in full duplex mode
done.
Apr 22 13:21:45 IZC1S100 [LOG_INFO] kernel: netlog:eth-s3p1 .. enabling 10baseT/UTP eApr 22 13:21:45 IZC1S100 [LOG_INFO] kernel: netlog:eth-s2p1 .. enabling 100baseTX/UTeApr 22 13:21:45 IZC1S100 [LOG_INFO] kernel: netlog:eth-s1p1 .. enabling 100baseTX/UTefw driver loadable interface called.
FW-1: 2 interfaces installed
Generating config files for IZC1S100: ipsrd hosts password group resolver snmp inetd.Fri Apr 22 13:22:01 JST 2005
Apr 22 13:22:02 IZC1S100 [LOG_ERR] xntpd[222]: sendto(211.19.45.231): Can't assign rs
IPSO (IZC1S100) (ttyd0)
login: Informatory: the current VPN-1 & FireWall-1 license allows only 100 internal .If this is different from the license you intended to purchase, ensure that you have.See
for troubleshooting.
Informatory: the current VPN-1 & FireWall-1 license allows only 100 internal hosts.
If this is different from the license you intended to purchase, ensure that you have.See
for troubleshooting.
vpn1 driver loadable interface called.
VPN-1: Cryptographic algorithm tests passed successfully
VPN-1: connected to FW-1
IPSO (IZC1S100) (ttyd0)
login: admin
Password:
Apr 22 13:23:32 IZC1S100 [LOG_NOTICE] login: authentication failure; root(uid=0) -> e
So, may I ask, what is the default login/password.? Cheers.
Mark Sargent.