How can I change IFC from S100 to D100? 1

[nlhtech]

I have a PRI between a Cisco Call manager and a Nortel Opt 61C. The link is causing BUG1369 messages. I have checked the settings in the call manager and the PRI Protocol Type is PRI DMS100. This appears to be the only option for a Nortel Switch. The 61c has IFC set as s100. I would like to try D100 but as can be seen from below, the switch will not allow mw to make the change.
Any suggestons?


PRI* TRK LOOP 26 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : NO ALARM
CH 01 - IDLE TIE VOD * CH 02 - IDLE TIE VOD *
CH 03 - IDLE TIE VOD * CH 04 - IDLE TIE VOD *
CH 05 - IDLE TIE VOD * CH 06 - IDLE TIE VOD *
CH 07 - IDLE TIE VOD * CH 08 - IDLE TIE VOD *
CH 09 - IDLE TIE VOD * CH 10 - IDLE TIE VOD *
CH 11 - IDLE TIE VOD * CH 12 - IDLE TIE VOD *
CH 13 - IDLE TIE VOD * CH 14 - IDLE TIE VOD *
CH 15 - IDLE TIE VOD * CH 16 - IDLE TIE VOD *
CH 17 - IDLE TIE VOD * CH 18 - IDLE TIE VOD *
CH 19 - IDLE TIE VOD * CH 20 - IDLE TIE VOD *
CH 21 - IDLE TIE VOD * CH 22 - IDLE TIE VOD *
CH 23 - IDLE TIE VOD * CH 24 - DCH 63
.****
OVL000
>ld 96
DCH000
.dis dch 63
.
DCH: 63 RLS CONFIRM TIME: 8:04:34 6/04/2006

****
OVL000
>ld 60
DTI000
.disl 26

OK
.****
OVL000
>ld 17
CFN000
MEM AVAIL: (U/P): 6431760 USED U P: 835497 187462 TOT: 7454719
DISK SPACE NEEDED: 353 KBYTES
2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED LD43 - BKO)
DCH AVAIL: 249 USED: 6 TOT: 255
AML AVAIL: 15 USED: 1 TOT: 16
REQ chg
TYPE adan
ADAN chg dch 63
CTYP MSDL
DNUM 07
PORT 1
DES CiscoCallMGR
DES
USR
IFC d100

SCH4752

IFC
DCHL
PRI
OTBF
DRAT
SIDE
RLS
RCAP
TIMR
LAPD

MEM AVAIL: (U/P): 6431760 USED U P: 835497 187462 TOT: 7454719
DISK SPACE NEEDED: 353 KBYTES
2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED LD43 - BKO)
DCH AVAIL: 249 USED: 6 TOT: 255
AML AVAIL: 15 USED: 1 TOT: 16

ADAN DATA CHGED
ADAN

REQ ****
OVL000
>ld 16
RDB000
MEM AVAIL: (U/P): 6431760 USED U P: 835497 187462 TOT: 7454719
DISK SPACE NEEDED: 353 KBYTES
2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED LD43 - BKO)
REQ chg
TYPE rdb
CUST 0
ROUT 98
DES
TKTP
ESN
CNVT
SAT
RCLS
DTRK YES
BRIP NO
ISDN yes
MODE
IFC d100
SCH4775
IFC
SBN
PNI
NCNA
NCRD
CHTY BCH
CTYP
INAC
ISAR
CPUB
DAPC
DSEL
PTYP
AUTO
ICOG
SRCH
TRMB
STEP
ACOD
TARG
BILN
OABS
INST
IDC
ANTK
SIGO
CNTL
CDR
MUS
RACD
FRL
TDET
TTBL
ALRM

MEM AVAIL: (U/P): 6431760 USED U P: 835497 187462 TOT: 7454719
DISK SPACE NEEDED: 353 KBYTES
2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED LD43 - BKO)
REQ
SCH0101
REQ
SCH0101
REQ ****
OVL000
>ld 60
DTI000
.enll 26

PRI000 26 15

PRI000 26 15

DTA023 26

OK
.
DCH: 63 EST CONFIRM TIME: 8:06:50 6/04/2006
stat 26

PRI* TRK LOOP 26 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : NO ALARM
CH 01 - IDLE TIE VOD * CH 02 - IDLE TIE VOD *
CH 03 - IDLE TIE VOD * CH 04 - IDLE TIE VOD *
CH 05 - IDLE TIE VOD * CH 06 - IDLE TIE VOD *
CH 07 - IDLE TIE VOD * CH 08 - IDLE TIE VOD *
CH 09 - IDLE TIE VOD * CH 10 - IDLE TIE VOD *
CH 11 - IDLE TIE VOD * CH 12 - IDLE TIE VOD *
CH 13 - IDLE TIE VOD * CH 14 - IDLE TIE VOD *
CH 15 - IDLE TIE VOD * CH 16 - IDLE TIE VOD *
CH 17 - IDLE TIE VOD * CH 18 - IDLE TIE VOD *
CH 19 - IDLE TIE VOD * CH 20 - IDLE TIE VOD *
CH 21 - IDLE TIE VOD * CH 22 - IDLE TIE VOD *
CH 23 - IDLE TIE VOD * CH 24 - DCH 63
.

 

[johnpoole]

out the trunks, then the dch then the route, put them back in.. then ld 96 dis msdl x all enl msdl x fdl, that reloads the data to the msdl

john poole
bellsouth business
columbia,sc

 

[johnpoole]

btw you need to ld 96 dis dch x auto ld 60 disl x to take the loop down before you can out it

john poole
bellsouth business
columbia,sc

 

[nlhtech]

Thanks John. I was hoping that there was an easier way. I guess I'll have to dig in and get at it.

nlhtech

 

[MG2005]

yes correct - you need S100 on the nortel side, DMS 100 on the cisco gateway side for this to work

also Nortel must be NETWORK side
Cisco USER side

 

[johnpoole]

also Nortel must be NETWORK side
Cisco USER side

that gives the ckt the nortel as the clock source, you can't clock off of that route.. i leave my clocks on the ld carrier.. then that route will clock off of the ld, the ccm will clock off of the tie, when the cisco dials the tdm, clocking is in sync..

john poole
bellsouth business
columbia,sc

 

[MG2005]

that gives the ckt the nortel as the clock source, you can't clock off of that route.. i leave my clocks on the ld carrier.. then that route will clock off of the ld, the ccm will clock off of the tie, when the cisco dials the tdm, clocking is in sync..
john poole
bellsouth business
columbia,sc

not if you specify EXT for CLOK