Help!!!!!! Cisco Router - Lucent Definity

[cgarcia]

HELP!!!

Hi,
I have a Router Cisco 3640 with NM-HDV-1E1-30E and PBX Lucent Definity G3 V.6i.
How to connect Cisco router with PBX???
I need a exmaple (configuration) for this connection???

Thank's

 

[BuckWeet]

How are you going to connect it to the definity, via PRI integration, T1 or what?

are you going to run DCS+ over this link, or just QSIG???

need more info before I can help you....


BuckWeet

 

[cgarcia]

The medium of connection for this router and definity, is a RJ45-BNC cable (RJ45 in Router and BNC in definity).
I used CAS signaling. (E1 R2)
I need a example configuration for this connection...

Regards.

 

[BuckWeet]

Here is a config that I just recently did with a Definity, this is doing T1 CAS Tie line trunks, with DCS over PPP...
we only did 12 trunks to, and ran this over frame relay..

This is a good working config, also make note that you should have the latest IOS in your router as well.



Coldwater_3620#sh run
Building configuration...

Current configuration : 3581 bytes
!
version 12.1
no service single-slot-reload-enable
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname Coldwater_3620
!
voice-card 1
!
ip subnet-zero
!
!
controller T1 1/0
framing esf
linecode b8zs
ds0-group 1 timeslots 1 type e&m-wink-start
ds0-group 2 timeslots 2 type e&m-wink-start
ds0-group 3 timeslots 3 type e&m-wink-start
ds0-group 4 timeslots 4 type e&m-wink-start
ds0-group 5 timeslots 5 type e&m-wink-start
ds0-group 6 timeslots 6 type e&m-wink-start
ds0-group 7 timeslots 7 type e&m-wink-start
ds0-group 8 timeslots 8 type e&m-wink-start
ds0-group 9 timeslots 9 type e&m-wink-start
ds0-group 10 timeslots 10 type e&m-wink-start
ds0-group 11 timeslots 11 type e&m-wink-start
ds0-group 12 timeslots 12 type e&m-wink-start
!
!
voice-port 1/0:2
timing in_digit_ignore 0
connection trunk 2222
!
voice-port 1/0:3
timing in_digit_ignore 0
connection trunk 2223
!
voice-port 1/0:4
timing in_digit_ignore 0
connection trunk 2224
!
voice-port 1/0:5
timing in_digit_ignore 0
connection trunk 2225
!
voice-port 1/0:6
timing in_digit_ignore 0
connection trunk 2226
!
voice-port 1/0:7
timing in_digit_ignore 0
connection trunk 2227
!
voice-port 1/0:8
timing in_digit_ignore 0
connection trunk 2228
!
voice-port 1/0:9
timing in_digit_ignore 0
connection trunk 2229
!
voice-port 1/0:10
timing in_digit_ignore 0
connection trunk 2230
!
voice-port 1/0:11
timing in_digit_ignore 0
connection trunk 2231
!
voice-port 1/0:12
timing in_digit_ignore 0
connection trunk 2232
!
voice-port 1/0:1
timing in_digit_ignore 0
connection trunk 2221
!
!
dial-peer voice 1 voip
destination-pattern 22..
dtmf-relay h245-alphanumeric
codec g729ar8
session target ipv4:192.168.10.1
!
dial-peer voice 1111 pots
destination-pattern 1111
port 1/0:1
!
dial-peer voice 1112 pots
destination-pattern 1112
port 1/0:2
!
dial-peer voice 1113 pots
destination-pattern 1113
port 1/0:3
!
dial-peer voice 1114 pots
destination-pattern 1114
port 1/0:4
!
dial-peer voice 1115 pots
destination-pattern 1115
port 1/0:5
!
dial-peer voice 1116 pots
destination-pattern 1116
port 1/0:6
!
dial-peer voice 1117 pots
destination-pattern 1117
port 1/0:7
!
dial-peer voice 1118 pots
destination-pattern 1118
port 1/0:8
!
dial-peer voice 1119 pots
destination-pattern 1119
port 1/0:9
!
dial-peer voice 1120 pots
destination-pattern 1120
port 1/0:10
!
dial-peer voice 1121 pots
destination-pattern 1121
port 1/0:11
!
dial-peer voice 1122 pots
destination-pattern 1122
port 1/0:12
!
!
!
interface Ethernet0/0
ip address 192.168.101.1 255.255.255.0
!
interface Serial0/0
bandwidth 1024
no ip address
encapsulation frame-relay IETF
service-module t1 timeslots 9-24
frame-relay lmi-type cisco
!
interface Serial0/0.1 point-to-point
ip address 192.168.10.2 255.255.255.252
frame-relay
!
router eigrp 10
network 192.168.10.0
network 192.168.101.0
no auto-summary
no eigrp log-neighbor-changes

 

[cgarcia]

Hi..
I used

ds0-group 1 timeslots 1 type r2-digital r2-comp ani

but, Lucent don't support r2-digital, only analog (Ref.

http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis3600/sw_conf/pbx_int/36lde1r2.pdf)

But, i configure the Cisco router with digital signal, because the communication not is correct for this configuration.

I need the configuration of remote site.
Thanks..