I have just completed upgrading a system to an AMD Athlon 1.33 GHZ. The only thing different is the motherboard, chip and case. All the old parts were thrown back into this new system. Everything seems to boot and work fine. But when I have to reboot the system, whether by menu or after loading driver, the hard drive is never found. The only way I can get the system to boot up successfully, is to hit "Reset" button or turn it off and then back on. I assume it has something with an old drive (10GB, 2 years old) and the speed of the system, but it boots 100% of the time when I hit the power switch or reset, and 0% of the time when I reboot using menu or any other method.
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations wOOdy-Soft on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Hard drive won't reboot
- Thread starter dgagne
- Start date
- Thread starter
- #3
I've set the mode in the bios to auto, and unless it's a cold boot...it won't boot up. I've even tried setting it as user and this way it doesn't have to try and find the drive each time, but still no luck. I've never seen anything like this. VERY STRANGE!!!
I have a similar problem. First, I fix computers for a local school and they gave a bunch of old machines. I got a old hard drive, 1.2 GB, about 4 years old, in one of these machines. So I used it in one of my spare machines for about 3 months and it was fine. Then I stopped using it for about 2 weeks and it never could find the hard drive. I tried bios tricks, hex editing the boot sector, component testing the drive controller and bus interface on the drive, and everything was fine. Then I took a look at my records for some of the work I did at the school. I fixed and replaced a hard drive after it was gutted by a virus. This virus was called "Stoned Monkey", and it has a few flavours. It was a boot sector virus and it sometimes infect a primary or secondary drive during POST and hard drive init during boot up. So this was the drive I replaced, the new drive, and after a few years, it still had the virus on it that was transferred from the old machine when I copied over some files.
One thing that got it working a few times was changing certain values in the bios. Now each bios is different in how it enumerates drives so sometimes this won't work ever, but changing some values like the "Block Mode" setting can sometimes get it going. Using "Auto" can stop it from working but LBA definately stops it working. Why? Well I don't know. Block mode transfer can stop it from working, but you generally get messages or something. I get nothing. I can start the machine, and it will do POST and then go to the device listings(Award BIOS. Has two screens, PNP and Drive info and then a new screen that has the other resources displayed) and then the floppy drive will drive for about 20 seconds and stop(If it is in the drive of course!) or if it just has a hard drive, nothing. It should say "Starting Windows 98..." or whatever I am using on my c: drive or floppy. But I get a blinking cursor and that is all. If I insert a bootable cd(Windows ME is one of them), it will boot to the CD boot menu. If you get access to DOS then you can access c: but you just can't boot.
But, even after formatting the drive, at least 6 times, with low level formatting and taking about 20 hours for a 10 pass all zero format, the virus has popped up again. I had the drive in my machine for about 3 minutes today, which is about a year later, and my other(current drive) is now not being picked up, even though I was using it for 6 months and no errors ever. So if you do have a drive that is doing that, it could be a virus, it could remanants of a past infection, it could be a setting in your bios(you can sometimes change some BIOS settings from Windows but only using specific tools eg. direct drive access tools.), or you just have a plain old drive failure and you need to replace it. Strange.
One thing that got it working a few times was changing certain values in the bios. Now each bios is different in how it enumerates drives so sometimes this won't work ever, but changing some values like the "Block Mode" setting can sometimes get it going. Using "Auto" can stop it from working but LBA definately stops it working. Why? Well I don't know. Block mode transfer can stop it from working, but you generally get messages or something. I get nothing. I can start the machine, and it will do POST and then go to the device listings(Award BIOS. Has two screens, PNP and Drive info and then a new screen that has the other resources displayed) and then the floppy drive will drive for about 20 seconds and stop(If it is in the drive of course!) or if it just has a hard drive, nothing. It should say "Starting Windows 98..." or whatever I am using on my c: drive or floppy. But I get a blinking cursor and that is all. If I insert a bootable cd(Windows ME is one of them), it will boot to the CD boot menu. If you get access to DOS then you can access c: but you just can't boot.
But, even after formatting the drive, at least 6 times, with low level formatting and taking about 20 hours for a 10 pass all zero format, the virus has popped up again. I had the drive in my machine for about 3 minutes today, which is about a year later, and my other(current drive) is now not being picked up, even though I was using it for 6 months and no errors ever. So if you do have a drive that is doing that, it could be a virus, it could remanants of a past infection, it could be a setting in your bios(you can sometimes change some BIOS settings from Windows but only using specific tools eg. direct drive access tools.), or you just have a plain old drive failure and you need to replace it. Strange.
- Status
Similar threads
