g3v4 ISDN-PRI setup

[AVAYAPro]

I have been working on setting this circuit up for the better part of 2 days now.

Does anyone have a sample configuration?

I have set the circuit up just like I would on a Communication Manager system. I have a feeling my configuration is incorrect, seeing as how this is a very dated system.

HELP!!!

Thanks.

 

[AVAYAPro]

oh, the circuit pack is a tn767 and it is connected to the NetPOP via a Paradyne 3160.

crossover needed?

 

[lopes1211]

Depends on your platform. If it's a g3R, the config would be just like Comm Mgr and require a TN464. If it is a g3i or g3si, or g3vs, there is a bit more to it. See:

http://www.tek-tips.com/viewthread.cfm?qid=1539486&page=3

-CL

 

[AVAYAPro]

how do i tell? the system-parameters customer options page just says g3v4.

 

[lopes1211]

What is the processor? TN786 would be the i/si/vs with the flashcard. The G3R will have a disk drive, tape and The process I believe was a UN332,

-CL

 

[AVAYAPro]

tn786

 

[lopes1211]

In that case, the following should tell you everyhting you need:

http://www.tek-tips.com/viewthread.cfm?qid=1539486&page=3

-CL

 

[AVAYAPro]

all has been configured. we must be getting somewhere.

the signaling group is still out-of-service but the status of the trunk group is OOS/FE-idle.

 

[AVAYAPro]

signaling group is in-service, trunk group is OOS/FE-idle

sorry.

 

[lopes1211]

FE is far end so maybe they just haven't turned up the B channels yet. Call them and find out.

-CL

 

[AvayaTier3]

what protocol is the provider using?
NI1 = a protocol
NI2 = b protocol

o A = Custom or NI1. This is typically used when your T1 comes out of an AT&T
4ESS Central Office.
o B = NI2, and is typically used when your T1 comes out of a 5ESS Central Office
This is the only protocol capable of giving the customer NAME and number
Caller ID. You always prefer this protocol if the vendor can provide it!


If it's not coming up, you most likely don't match the provider.

protocol on ds1 form, trunk-group form, signal-group form

example below is NI2 (b protocol) used for name and number caller ID

display ds1 1a12
DS1 CIRCUIT PACK

Location: 01A12 Name: Opt. Light Path
Bit Rate: 1.544 Line Coding: b8zs
Line Compensation: 1 Framing Mode: esf
Signaling Mode: isdn-pri
Connect: network
Country Protocol: 1
Protocol Version: b
CRC? n
Idle Code: 11111111
DCP/Analog Bearer Capability: 3.1kHz

Slip Detection? n
--------------------------------------------------------------------------------
change signaling-group 1 Page 1 of 5
SIGNALING GROUP
Primary D-Channel: 01A1224 Max number of CA TSC: 0
Trunk Group for Channel Selection: 2
Supplementary Service Protocol: b
--------------------------------------------------------------------------------
change trunk-group 2 Page 1 of 10

Supplementary Service Protocol: b


A great teacher, does not provide answers, but methods to teach others "How and where to find the answers"

bsh

35 years Bell, AT&T, Lucent, Avaya
Tier 3 for 25 years and counting

http://bshtele.com

 

[AvayaTier3]

# this was when all was set to "Supplementary Service Protocol: a" on the
# trunk-group and on signaling-group and "Protocol Version: a" on the ds1 form and the provider using "b" protocol will look something like this.

status trunk 2

TRUNK GROUP STATUS

Member Port Service State Mtce Connected Ports
Busy

02/01 01A1201 OOS/FE-PINS-idle no
02/02 01A1202 OOS/FE-PINS-idle no


A great teacher, does not provide answers, but methods to teach others "How and where to find the answers"

bsh

35 years Bell, AT&T, Lucent, Avaya
Tier 3 for 25 years and counting

http://bshtele.com

 

[AVAYAPro]

i have followed the instructions on this page to a T. any other suggestions?

i am still showing comm link in-service, signaling group in-service, trunk group oof/fe-idle

service provider tells me that all b channels are up.

HELP!!!