FDL for 3900's

[Goodnight1880]

I built the fdl in ld 97 to run this morning at 01:00 hrs. I've checked my fsum in ld 32 and no change to the sets that needed updating. Did I miss a step.

FDL DATA
SET TYPE: ALL

DAY: THURSDAY NUMBER OF INTERVALS: 01
INT 01 02
FRCE: NO
FVER: 00

 

[johnpoole]

here's a page i copied from a post here, it should help.

ld 97
REQ chg
TYPE fdl
FDTP 3904
FDTM yes – Say yes if you want to schedule the download, Say no if want it to start immediately

FDAY 5 1 – FDAY d n Day and number of time intervals for download (if you said yes to FDTM)
d= (0-6) Day of the week, Sunday to Saturday
n= (0-4) Number of intervals where 0= no download for that day
note: If two or more intervals are specified, they must be non overlapping,
non consecutive and in increasing order.
FDAY is re-prompted until <cr> is entered.

FINT 3 2 – FINT s l Starting hour and length for a time interval.
s= (0-23) Starting hour using 24 hour format
l= (1-24) Length of interval in hours
FINT is prompted n times if Number of Intervals is > 0

FDAY <cr> -- FDAY is re-prompted until <cr> is entered.

FTNR yes – Say yes to download to specific range of TNs, Do not say no to this or all 3904’s will download

FSTN 52 0 11 0 Start

FETN 52 0 11 4 End

FDNR no – enter no because we don’t want to select specific DN’s for download.

FRCE yes – Say yes to force the download regardless of the 3904’s current flash firmware version.

FVER <cr>


MEM AVAIL: (U/P): 23534388 USED U P: 4855751 429313 TOT: 28819452
DISK SPACE NEEDED: 698 KBYTES
2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED LD43 - BKO)

REQ ****
OVL000

john poole
bellsouth business
columbia,sc

 

[Goodnight1880]

Is there anything in ld 32 that has to be done. FDLS? I've done that now and didn't do yesterday. I noticed in doc's it says "intiate system wide flash download" and when I do this it says it's building tree and then I get a sdl005 err saying the download was stopped.

John I opened a thread yesterday about mdp refresh and no one has responded. I have a CS 1000m (81c) with SS. My question is does this procedure auto remove obsolete peps and defective peps. And should I do this through the SS? I used the MIRCC and have a nice size delta to load. thanks

BG

 

[johnpoole]

ld 32 fdls.. that builds the tree then the next day
fsum all

john poole
bellsouth business
columbia,sc

 

[johnpoole]

you may have not gotten a response because that is such a new rls.. i download a new dep list from nortel and load it, which blows away the old.. i'm on rls 3 and haven't read up on the refresh command..

john poole
bellsouth business
columbia,sc

 

[Goodnight1880]

10-4 on the fdl...

Yeah I'm 4.5W and the doc's seem to make it sound like doing this through the SS will be the best. I just din't want to load the delta and have peps sitting there that needed to be removed. Thanks for you help.

 

[janeenaj]

you will need to remove the obsolete and defective, before you put on the delta. I believe it even say that somewhere on the MIRCC report toward the bottom of the page