DSC problem

[rsadf2006]

Hi all

I have an problem , when anyone calls from remote system ( CS1000M rel. 6) I got H2586 instead of 2502586. It means there is no DSC number.

I have tried to resolve this issue but unfortunately I could not do anything.

Thank you

 

[Firebird Scrambler]

If you want to remove the "H", then a plugin (14)needs to be enabled first.

From Release 25.15 onwards a number of Product Improvement Patches (PIs) have been built into the software. These are called PLUGINs

To List/Enable/Disable these PLUGINs use the following commands

First login to pdt. NB All commands are in lowercase

1. To list status of all PLUGINs plp (PLP)
2. To list status of individual PLUGINs plp # (PLP #) where # is the PLUGIN number 0 - 14
3. To enable PLUGIN ple # (PLE #) where # is the PLUGIN number 0 - 14
4. To disable PLUGIN pld # (PLD #) where # is the PLUGIN number 0 - 14

LIST OF PLUGINS

PLUGIN # PRS# Patch # Description
0 BV67946 Wrong Special Dial Tone with NT8D17CA CONF/TDS pack.
1 BV63269 MPLR12002 BRI B-Channels not marked MBSY, When D Channel Drops.
2 BV69389 Automatic Wake-up is turned off if INI occurs.
3 BV69237 MPLR11506 Hotline Enhancement for BASF.
4 BV19192 MPLR01862 After dialling a LSC followed by a DSC the user gets overflow tone
5 BV71211 NRGA is not workingwith Tandem Node & Digit Manipulation.
6 BV28124 MPLR02056 BCS set cannot release from call transfer to Attendant.
7 MP05648 DID with DNIS & IDC cannot call PLDN using SCLU.
8 MP05649 Not possible to CFW a set to PLDN using SCLU.
9 BV41730/40697 Wrong display if Att extends call with announcement.
10 BV42928 MPLR07615 CFW calls to NAS is intercepted to Nite Dn.
11 BV62151 MPLR11339 RAN cannot be accessed via route acod over network.
12 BV63726 MPLR08777 Mtce messages flooding TTY, TTY unusable.
13 BV71206 MCT should be output on answer from 500 set.
14 BV70355 MPLR09806 MCDN - Orig Dn in Display is preceded with "H"


All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[rsadf2006]

Hi all

first, I would like to thank firebirdscrambler for his post solution , but when I did same problem still there.

Second, I will explain again my issue " I have two site connected to each other through TIE trunk.
And I define LSC xxx for site 1 and yyy for site 2
but when you call from site 1 to site 2 through TIE trunk to specific extension, I got a number containing (DSC + DN) , but the problem is when you call from site 2 to site 1 through TIE trunk to specific extension, I got a number (H+DN). In this case the one who answering the phone in the site 1 doesn't know the calling person.

Is there any way to solve this problem

I appreciate any help

 

[johnpoole]

post the build on your dch

john poole
bellsouth business
columbia,sc

 

[rsadf2006]

In the following lines you will find the configuration for DCH , Trunk and Route for both sites

For site 1

DCH configuration
ADAN DCH 27
CTYP MSDL
GRP 0
DNUM 11
PORT 1
DES SITE 2
USR PRI
DCHL 23
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
NASA NO
IFC SL1
SIDE NET
SEMT 1
CNEG 1
RLS ID 25
RCAP ND2
MBGA NO
OVLR NO
OVLS NO
T200 3
T203 10
N200 3
N201 260
K 7
----------
Trunk configuration

TN 23 1
DATE
PAGE
DES SITE 2
DES SITE 1
TN 023 01
TYPE TIE
CDEN SD
CUST 0
TRK PRI2
PDCA 1
PCML MU
NCOS 7
RTMB 66 1
B-CHANNEL SIGNALING
TGAR 0
AST NO
IAPG 0
CLS SRE DTN WTA LPR APN THFD XREP BARD
P10 VNL
TKID
AACR NO

--------

Route configuration

TYPE RDB
CUST 00
ROUT 66
DES SITE 2
TKTP TIE
NPID_TBL_NUM 0
ESN NO
RPA NO
CNVT NO
SAT NO
IDEF NET
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC SL1
PNI 00001
NCNA YES
NCRD YES
TRO NO
CTYP UKWN
INAC NO
ISAR NO
DAPC NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 8425
TCPP NO
TARG 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 1 *
NDNO 1
DEXT YES
DNAM YES
SIGO STD
MFC NO
ICIS YES
OGIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896


PAGE 002

SFB 3
NBS 2048
NBL 4096
TFD 0
DTD NO
SCDT NO
2 DT NO
DRNG NO
CDR YES
INC YES
LAST NO
QREC NO
OAL YES
AIA YES
OAN YES
OPD NO
NDP EXC 0
CDRX NO
NATL YES
SSL
CFWR NO
IDOP NO
MUS YES
MRT 100
PANS YES
FRL 0 7
FRL 1 7
FRL 2 7
FRL 3 7
FRL 4 6
FRL 5 6
FRL 6 7
FRL 7 6
AUTH NO
TTBL 0
ATAN NO
PLEV 2
OPR NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 1008425 66
SGRP 0
AACR N
==========

For SITE 2

DCH configuration

ADAN DCH 26
CTYP MSDL
GRP 0
DNUM 11
PORT 0
DES SITE 1
USR PRI
DCHL 22
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
NASA NO
IFC SL1
SIDE USR
CNEG 1
RLS ID 25
RCAP ND2
MBGA NO
OVLR NO
OVLS NO
T200 3
T203 10
N200 3
N201 260
K 7

------

Trunk configuration

TN 22 1
DATE
PAGE
DES
DES SITE 1
TN 023 01
TYPE TIE
CDEN SD
CUST 0
TRK PRI2
PDCA 1
PCML MU
NCOS 7
RTMB 118 1
B-CHANNEL SIGNALING
TGAR 0
AST NO
IAPG 0
CLS SRE DTN WTA LPR APN THFD XREP BARD
P10 VNL
TKID
AACR NO


---------
Route configuration

TYPE RDB
CUST 00
ROUT 118
DES SITE 1
TKTP TIE
NPID_TBL_NUM 0
ESN NO
RPA NO
CNVT NO
SAT NO
IDEF NET
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC SL1
PNI 00001
NCNA YES
NCRD YES
TRO YES
CTYP CDP
INAC NO
ISAR NO
DAPC NO
MBXR NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 8425
TCPP NO
PII NO
AUXP NO
TARG 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 1 *
NDNO 1
DEXT YES
DNAM YES
SIGO STD
MFC NO
ICIS YES
OGIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896


PAGE 002

SFB 3
NBS 2048
NBL 4096
TFD 0
DTD NO
SCDT NO
2 DT NO
DRNG YES
CDR NO
INC YES
LAST NO
QREC NO
OAL YES
AIA YES
OAN YES
OPD NO
NDP EXC 0
CDRX NO
NATL YES
SSL
CFWR NO
IDOP NO
MUS NO
MRT 100
PANS YES
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 4
FRL 5 5
FRL 6 6
FRL 7 7
AUTH NO
TTBL 0
ATAN NO
PLEV 2
OPR NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 1008425 66
SGRP 0
AACR N

 

[rsadf2006]

Hi all

For now we have not received any comment about our system's configuration

If there is any answer we appreciate it'

Thank you

 

[SL1M1]

Try Site 1 and look at CALL TYPE 'CTYP' in RDB (RouteDataBlock)
Change this to CDP in the ISDN Parameters, see what happens

Cheers!!

 

[rsadf2006]

Hi SL1M1

I already change it to CDP

but unfortunately the result same (Nothing change)

Thank u

any more notes

 

[SL1M1]

OK other areas Could be a DMI setting 'CTYP' / Dchannel/MSDL config needs ForceDownLoad ?

Cheers!!

 

[kprintz]

Sounds like a CLID issue. Compare/post your CLID data in CDB in both PBXs.

LD 21
PRT
TYPE
CLID