setprogram
Technical User
This is all I could find on installing a new DID...
How To Install DIDs on a 8X24
faq799-2467
Posted: 17 Sep 02
Installing the cards
Power down just the trunk module, put your cards in and power it back up.
A. Configuration – Next until you see
D. Maintenance – Show
1. System version – Next to
3. Module status – Show
Show module – Show
XX sets on KSU – Next
XX Lines on KSU – Next
Module 3 empty -
Programming the Target Lines
A. Configuration – Show
1. Trk/ Line Data – Show
Show line: Dial in 081 (this is your first target line) Target lines number 081-184
Rec’d #: None – Press Change
Rec’d #: dial in the digits being sent by telco. Then press Next
Line Data – Show
Line Type: Public – Press Change
Private To: dial the ext # you want to have the target line show up on.
Press Next
PrimeSet: 221 (operator) – Next
Aux: Ringer: Y – Next
Auto Privacy: Y – Next
Show line: dial the next target line number 082
Program one target line for each DID. Then assign the target line to the phone (see below):
Assigning the Line:
Press your Header button until you see:
A.Configuration
1. Trk/ Line data – Next
2. Line Access – Show
Show set: dial the ext. number
Line assignment – Show
No lines assigned (make sure only the lines you want to appear on the phn are assigned, otherwise remove them)
Press Add
Add Line: dial in target line number (ie., 081)
Line081 assigned – Next
Answer DNS – Next
Ringing – Show
Line 081 – Ring……
Press Header button twice and you’ll be back to
Show set - enter in the next extension number and continue assigning all your target lines to the appropriate extensions.
We have a MICS 4.5. and we are porting in a number. This is my question or questions. These instructions tell you to 'dial' in the number. I've programmed and assigned target lines using a four digit DID and extension. Are these instructions the ones used to enter a complete number or does the Telco send only the last 4 digits to the PRI? Oh and would our line carrier send a new card to Install?
Thanks for helping me understand...
How To Install DIDs on a 8X24
faq799-2467
Posted: 17 Sep 02
Installing the cards
Power down just the trunk module, put your cards in and power it back up.
A. Configuration – Next until you see
D. Maintenance – Show
1. System version – Next to
3. Module status – Show
Show module – Show
XX sets on KSU – Next
XX Lines on KSU – Next
Module 3 empty -
Programming the Target Lines
A. Configuration – Show
1. Trk/ Line Data – Show
Show line: Dial in 081 (this is your first target line) Target lines number 081-184
Rec’d #: None – Press Change
Rec’d #: dial in the digits being sent by telco. Then press Next
Line Data – Show
Line Type: Public – Press Change
Private To: dial the ext # you want to have the target line show up on.
Press Next
PrimeSet: 221 (operator) – Next
Aux: Ringer: Y – Next
Auto Privacy: Y – Next
Show line: dial the next target line number 082
Program one target line for each DID. Then assign the target line to the phone (see below):
Assigning the Line:
Press your Header button until you see:
A.Configuration
1. Trk/ Line data – Next
2. Line Access – Show
Show set: dial the ext. number
Line assignment – Show
No lines assigned (make sure only the lines you want to appear on the phn are assigned, otherwise remove them)
Press Add
Add Line: dial in target line number (ie., 081)
Line081 assigned – Next
Answer DNS – Next
Ringing – Show
Line 081 – Ring……
Press Header button twice and you’ll be back to
Show set - enter in the next extension number and continue assigning all your target lines to the appropriate extensions.
We have a MICS 4.5. and we are porting in a number. This is my question or questions. These instructions tell you to 'dial' in the number. I've programmed and assigned target lines using a four digit DID and extension. Are these instructions the ones used to enter a complete number or does the Telco send only the last 4 digits to the PRI? Oh and would our line carrier send a new card to Install?
Thanks for helping me understand...
