Disable hipath 4000 alarms from cdr

[hipath0514]

Hi,

Need help on how can i disable alarms in hipath 4000 from logging in the cdr capture in service/ atlantic port?


Thanks in advance

Hipath0514

 

[sbcsu]

If you need the CDR use port 1202
If you need the Alarms use port 1201

 

[Iamnothere]

Precisely

 

[hipath0514]

Thanks for your reply.

I have try to change the cdr port to 1202 but there is no cdr being captured on the hyperterminal. I was able to do a command in hipath using this port but cdr is not dumping.

Below is the configuration of cdr.

<dis-sels
SELGRNO = 1;
DIS-SELS:1;
H500: AMO SELS STARTED

OPERATING CONDITIONS OF THE SELECTION GROUPS

SELGRNO OPERATING CONDITION

1 ON

AMO-SELS -111 SMDR/DMDR SELECTION GROUP SWITCHES
DISPLAY COMPLETED;
<dis-selg
SELGNO = 1;
DIS-SELG:1;
H500: AMO SELG STARTED

+==============================================================================+
| SELECTION GROUP : 1 |
+------------------------------------------------------------------------------+
| |
| OPERATING STATE : ON |
| |
| RESOP : Y |
| BASDEV : DEV3 BLBAS : 1 |
| RESDEV : DEV1 BLRES : 1 |
| |
+==============================================================================+
| |
| SELECTION GROUP : 1 SELECTION TABLE : 1 |
| |
| FORMBAS : FORM05 TARIFF : NOCALC |
| FORMRES : FORM05 DESTCNT : A22 |
| |
| LEVEL0 : 0&&999 |
| LEVEL1 : 0 |
| LEVEL2 : 0 |
| CDRCD : 0&&999 |
| |
| ATNDGR : 0&&15 |
| SERVICE : VOICE |
| |
| CDRULT : 0 CONNTL : 00 : 00 : 01 |
| COPIN : 0&&15 CARRIER : 0&&9 |
| |
| SELECTION FEATURES 1 : |
| |
| CTYPE : ALL PAYPARTY : ALL NSTAT : N |
| CDRAC : N SFSETUP : N CDBAD : N |
| CDRC : N CDRSTA : N THRGCON : Y |
| SECTION : N TIE-LINE : N EXPENS : N |
| CONNTYP : INTERN &INCO &OUTG |
| RECTYP : ALL |
| |
| SELECTION FEATURES 2 : |
| |
| CDCHU : N CDRULTE : N CONNT : N |
| PCODE : N PPCF : N STATAB1 : N |
| STATAB2 : N DNOTBL1 : N DNOTBL2 : N |
| |
+==============================================================================+

AMO-SELG -111 ADMINISTRATION OF SELECTION GROUPS AND TABLES
DISPLAY COMPLETED;
<

ADD-SELG:SELG,1,Y,DEV3,DEV1,1,1;
CHANGE-SELG:SELT,1,1,FORM05,FORM05,NOCALC,A22;
CHANGE-SELG:SELT,1,1,,,,,0&&999
;
CHANGE-SELG:SELT,1,1,,,,,,VOICE ;
CHANGE-SELG:SELT,1,1,,,,,,,0&&15;
CHANGE-SELG:SELT,1,1,,,,,,,,ALL,ALL,N,N,Y,N,N,N,N,N,N,N,N,N,N,N,N,N,N;
CHANGE-SELG:SELT,1,1,,,,,,,,,,,,,,,,,,,,,,,,,,,0,000001;
CHANGE-SELG:SELT,1,1,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
0&&999,
0,
0;
CHANGE-SELG:SELT,1,1,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,N,N,
INTERN&INCO&OUTG
,0&&15,0&&9,ALL;


Thanks

 

[sbcsu]

Type in
DIS-LSSM;
It will show you what is active or not.
If there is nothing showing up on the CDR port 1202 then
DIS-SELS;
Which ever one is set to ON example 1
then
DEA-SELS:1;
ACT-SELS:1;
Then display again
DIS-LSSM;

If you are connected via hyperterminal: connect to the Atlantic LAN using 192.0.2.99 on your PC, set the destination on hyperterminal to be 192.0.2.3 port 1202

 

[sbcsu]

Are you sorted?

 

[hipath0514]

Hi,

Sorry for late reply

I have tried to change the port settings to 1202 but still raw data is not dumping.

But when i try to make a command via that 1202 port it is working. Do i need to configure something?

Many Thanks

 

[sbcsu]

again you need to
DEA-SELS
then
ACT-SELS

 

[hipath0514]

Hi,

I have deactivate and activate the SELS but still no raw data is dumping.

Please see below configuration,

DIS-LSSM;
H500: AMO LSSM STARTED

+=========================================================================+
| STATE OF LAN - CHANNELS |
+=========================================================================+
| | | SYSTEM | USER |
| TCP- | STATE |=========================================================|
| LINE | | IP ADRESS | PORT | IP ADRESS | PORT |
+=========================================================================+
| 1 | ON | 192.0.2.3 | 1201 | 0.0.0.0 | 0 |
| 2 | ON | 192.0.2.3 | 1202 | 192.0.2.46 | 62967 |
| 3 | OFF | 0.0.0.0 | 0 | 0.0.0.0 | 0 |
| 4 | OFF | 0.0.0.0 | 0 | 0.0.0.0 | 0 |
| 5 | OFF | 0.0.0.0 | 0 | 0.0.0.0 | 0 |
| 6 | OFF | 0.0.0.0 | 0 | 0.0.0.0 | 0 |
+=========================================================================+

AMO-LSSM -111 LINE SWITCH, SERVICE MODULES
DISPLAY COMPLETED;
<dea-sels
SELGRNO = 1;
DEA-SELS:1;
H500: AMO SELS STARTED

AMO-SELS -111 SMDR/DMDR SELECTION GROUP SWITCHES
DEACTIVATE COMPLETED;
<ac-sels
SELGRNO = 1;
AC-SELS:1;
H500: AMO SELS STARTED

AMO-SELS -111 SMDR/DMDR SELECTION GROUP SWITCHES
ACTIVATE COMPLETED;

DIS-SELS;
H500: AMO SELS STARTED

OPERATING CONDITIONS OF THE SELECTION GROUPS

SELGRNO OPERATING CONDITION

1 ON
2 OFF
3 OFF
4 OFF

AMO-SELS -111 SMDR/DMDR SELECTION GROUP SWITCHES
DISPLAY COMPLETED;

<dis-selg
SELGNO = 1;
DIS-SELG:1;
H500: AMO SELG STARTED

+==============================================================================+
| SELECTION GROUP : 1 |
+------------------------------------------------------------------------------+
| |
| OPERATING STATE : ON |
| |
| RESOP : Y |
| BASDEV : DEV3 BLBAS : 1 |
| RESDEV : DEV1 BLRES : 1 |
| |
+==============================================================================+
| |
| SELECTION GROUP : 1 SELECTION TABLE : 1 |
| |
| FORMBAS : FORM05 TARIFF : NOCALC |
| FORMRES : FORM05 DESTCNT : A22 |
| |
| LEVEL0 : 0&&999 |
| LEVEL1 : 0 |
| LEVEL2 : 0 |
| CDRCD : 0&&999 |
| |
| ATNDGR : 0&&15 |
| SERVICE : VOICE |
| |
| CDRULT : 0 CONNTL : 00 : 00 : 01 |
| COPIN : 0&&15 CARRIER : 0&&9 |
| |
| SELECTION FEATURES 1 : |
| |
| CTYPE : ALL PAYPARTY : ALL NSTAT : N |
| CDRAC : N SFSETUP : N CDBAD : N |
| CDRC : N CDRSTA : N THRGCON : Y |
| SECTION : N TIE-LINE : N EXPENS : N |
| CONNTYP : INTERN &INCO &OUTG |
| RECTYP : ALL |
| |
| SELECTION FEATURES 2 : |
| |
| CDCHU : N CDRULTE : N CONNT : N |
| PCODE : N PPCF : N STATAB1 : N |
| STATAB2 : N DNOTBL1 : N DNOTBL2 : N |
| |
+==============================================================================+

AMO-SELG -111 ADMINISTRATION OF SELECTION GROUPS AND TABLES
DISPLAY COMPLETED;
<


Many Thanks