Dedicated trunk for emergency phone

[mx103]

I have to build an elevator emergency phone dedicated to a single line trunk. I dont know what to set at the station TN to only use this trunk.

thanks in advance


I have my route and trunk built as follows:

TYPE TLS
TKTP COT
ROUT 9
TN 004 1 01 00 MBER 1

TYPE TNB
TN 4 1 1 0
DATE
PAGE
DES

TN 004 1 01 00
TYPE COT
CDEN 8D
CUST 0
XTRK XUT
TIMP 600
BIMP 3COM
NCOS 0
RTMB 9 1
NITE
SIGL GRD
SUPN NO
CLS UNR DIP WTA LPR APN PIP THFD
P10 TRC
DATE 9 MAY 2011


REQ PRT
TYPE RDB
CUST 0
ROUT 9

TYPE RDB
CUST 00
ROUT 9
TKTP COT
PRIV NO
SAT NO
RCLS EXT
DTRK NO
PTYP ACO
AUTO NO
ICOG IAO
SRCH LIN
STEP
ACOD 809
TARG 15
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 512
GRD 896
TFD 0
LEXT 100
SST 3 0
NEDC ETH
FEDC ORG
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
DRNG NO
CDR YES
INC NO
QREC YES
OAL YES
AIA YES
OAN YES
OPD YES
NATL YES
MUS YES
MRT 11
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
MANO NO
OHQ NO
OHQT 00
OHTD NO

REQ

 

[RickyPone]

You probably need to build a 500 tn.

 

[mx103]

I have the 500 set built but I'd like to be able to assign my office phone to the trunk to be able to test it.

 

[bhassell2000]

to have the COT line routed to this line build it with the PRDN



TN 008 0 00 01
TYPE COT
CDEN 8D
CUST 0
XTRK XUT
TIMP 600
BIMP 3COM
TRK ANLG
NCOS 5
RTMB 11 1
PRDN 4551
CMF NO
SIGL LOP
SUPN YES
STYP PIP
AST NO
IAPG 0
CLS UNR DTN WTA LPR APN THFA
P10 NTC
TKID
DATE 8 SEP 2002


Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/in/buddyhassell

 

[mx103]

I probably should have mentioned its for outbound use.

 

[mx103]

I guess my question should be how do I ensure my emergency phone only uses route 9 when I pick up the phone?

thanks

 

[nessman]

If it's a single POTS line you're looking to dedicate just for the elevator then just go directly from the demarc to the elevator, this way if the PBX goes down, the phone won't go down with it. Put an elevator phone with an auto-dialer on it. Done. I would also allow it to accept incoming calls too - in case of a true emergency, they can call whoever it is that's stuck in the elevator to update them or make sure they're OK.

I've always preached for emergency applications - to keep it as simple as possible. The fewer links in the chain, the more reliable it will be when it counts most.

But assuming you have a reason for doing it this way...

For an appearance on your office phone (I'm assuming just another digital or IP set), KEY xx PVR 4551 (or if you don't want it hear it ring - replace PVR with PVN). For the route to be outgoing only, change your RDB so that ICOG = OGT.

 

[RickyPone]

I'm not following how you have wired this. Do you have a 500 tn or a cot connected to the elevator?

 

[mx103]

thanks for the help so far.

To answer some questions

I don't have a POTS I have a ground start trunk.

I have the 500 set wired to a TN not the COT.
The 500 set tn will be configured with hot d to a monitoring center

 

[RickyPone]

Ok so you want the 500 port, that is wired to the elevator, to only go out route 9. Set up a targ for the route and then restrict the 500 port to that route via tgar.

 

[mx103]

Set up a targ for the route and then restrict the 500 port to that route via tgar.

can you give me direction on how to do this?

thanks

 

[nessman]

http://www.ghtrout.com/files/TGAR_and_TARG_Help.html