CS1K 2 PRI's in 2 different cabinets same route, route set for LIN 1

[PDL123]

CS1K: Two PRI's in 2 different cabinets same route, route set for LIN although when dialing out it selects channel 23 on the 1st PRI and uses all channels for (acending for incoming) and (decending for outgoing) and the rolls over to the 2nd PRI. Any info would be greatly appreciated. Thanks, Printouts Below



REQ:
OVL000
>ld 21
PT1000

REQ:
AUD000
prt
TYPE: rdb
CUST 0
ROUT 0

TYPE RDB
CUST 00
ROUT 0
DES DID
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP DTI
ISDN NO
DSEL VOD
PTYP DCO
AUTO NO
DNIS YES
NDGT 4
DDLY NO
DCDR NO
ICOG ICT
STEP
ACOD 8000
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 1
NDNO 1 *
DNAM NO
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3

IENB 5
VSS 0
VGD 6
SST 5 0
NEDC ETH
FEDC ETH
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR YES
INC YES
LAST YES
QREC NO


PAGE 002

OAL YES
AIA YES
OAN YES
OPD YES
CDRX NO
NATL YES
VRAT NO
MUS YES
MRT 8
MANO NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
ATAN NO
OHTD NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO



REQ: ltm
CUST 0
ROUT 1

TYPE TLST
TKTP DID
ROUT 1
DES PRI
TN 021 01 MBER 1 WINDSTREAM
TN 021 02 MBER 2 WINDSTREAM
TN 021 03 MBER 3 WINDSTREAM
TN 021 04 MBER 4 WINDSTREAM
TN 021 05 MBER 5 WINDSTREAM
TN 021 06 MBER 6 WINDSTREAM
TN 021 07 MBER 7 WINDSTREAM
TN 021 08 MBER 8 WINDSTREAM
TN 021 09 MBER 9 WINDSTREAM
TN 021 10 MBER 10 WINDSTREAM
TN 021 11 MBER 11 WINDSTREAM
TN 021 12 MBER 12 WINDSTREAM
TN 021 13 MBER 13 WINDSTREAM
TN 021 14 MBER 14 WINDSTREAM
TN 021 15 MBER 15 WINDSTREAM
TN 021 16 MBER 16 WINDSTREAM
TN 021 17 MBER 17 WINDSTREAM
TN 021 18 MBER 18 WINDSTREAM
TN 021 19 MBER 19 WINDSTREAM
TN 021 20 MBER 20 WINDSTREAM
TN 021 21 MBER 21 WINDSTREAM
TN 021 22 MBER 22 WINDSTREAM
TN 021 23 MBER 23 WINDSTREAM
TN 057 01 MBER 24 WINDSTREAM
TN 057 02 MBER 25 WINDSTREAM
TN 057 03 MBER 26 WINDSTREAM
TN 057 04 MBER 27 WINDSTREAM
TN 057 05 MBER 28 WINDSTREAM
TN 057 06 MBER 29 WINDSTREAM
TN 057 07 MBER 30 WINDSTREAM
TN 057 08 MBER 31 WINDSTREAM
TN 057 09 MBER 32 WINDSTREAM
TN 057 10 MBER 33 WINDSTREAM
TN 057 11 MBER 34 WINDSTREAM
TN 057 12 MBER 35 WINDSTREAM
TN 057 13 MBER 36 WINDSTREAM
TN 057 14 MBER 37 WINDSTREAM
TN 057 15 MBER 38 WINDSTREAM
TN 057 16 MBER 39 WINDSTREAM
TN 057 17 MBER 40 WINDSTREAM
TN 057 18 MBER 41 WINDSTREAM
TN 057 19 MBER 42 WINDSTREAM
TN 057 20 MBER 43 WINDSTREAM
TN 057 21 MBER 44 WINDSTREAM
TN 057 22 MBER 45 WINDSTREAM
TN 057 23 MBER 46 WINDSTREAM



CUST 0
FEAT rlb
RLI 0

RLI 0
ENTR 0
LTER NO
ROUT 1
TOD 0 ON 1 ON 2 ON 3 ON
4 ON 5 ON 6 ON 7 ON
VNS NO
CNV NO
EXP NO
FRL 3
DMI 0
FCI 0
FSNI 0
SBOC NRR
IDBB DBA
IOHQ NO
OHQ NO
CBQ NO

ISET 0
NALT 5
MFRL 3
OVLL 0






PDL

 

[RickyPone]

I think that has to do with the order in which the loops were enabled. Shouldn't be an issue though.

 

[PDL123]

That probably the order I enabled them, Thanks for the Info

 

[GHTROUT]

On large systems, the PBX will always select a TN in the same network group as the user, if the route has TNs in two or more groups. Even if the first choice out is in a different network group, it will prefer its own network group before it trues the programmed first choice out.

It might be the same for small systems in selecting cabinets. Try to originate a call from both cabinets and see if it acts differently for each.

--
Nortel Resources at GHTROUT.com World Famous!
--