CS1000 to AudioCodes

[pbxn]

Any one run into setting up a Tie circuit between an 81 and an AudioCodes gw?
I've got a QSig PRI setup, loops are idle and established as is the D-ch.But if I port a DID across the tie using the standard cdp, flen 4, dmi 0, the 4 digit between the nortel and audio codes works, but breaks external inbound calling. Alternativley, if I out the cdp and build a dummy acd, maxp 1, ncfw to acod and extension, external inbound calling (dialing it full 9+) that works, but 4 digit routing doesn't. Targ is off route, NET_Data is wide open, ncos is clear and programmed as normal trunks that work. On failed calls you get a fast busy. Co has also looked at circuit provisioning. Located in the states so pretty sure E1 won't work. Thanks
ADAN DCH 3
CTYP MSDL
GRP 0
DNUM 6
PORT 1
DES PITA
USR PRI
DCHL 3
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ISGF
PINX_CUST 0
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID 36
RCAP COLP NDI CCBI PRI DV3I CTI QMWI
PR_TRIGS DIV 2 3
CNG 2 3
PR_RTN NO
MBGA NO
OVLR YES
DIDD 0
OVLS YES
OVLT 0
T310 120
T200 3
T203 10
N200 3
N201 260
K 7

DES PITA
TN 003 01
TYPE TIE
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 3
RTMB 35 1
B-CHANNEL SIGNALING
TGAR 1
AST NO
IAPG 0
CLS UNR DIP CND ECD WTA LPR APN THFD HKD SPCD
P10 VNL
TKID
AACR NO
DATE 16 JUN 2011

TYPE NET_DATA
CUST 00
OPT RTA
AC1 INTL NPA SPN NXX LOC
AC2
FNP YES
ISDN YES
VPNI 0
PNI 0
PINX_DN
MBG 0
BSGC 65535
PFX1
PFX2
HLOC
LSC
RCNT 5
PSTN NO
TNDM 15
PCMC 15
SATD 1
OCLI NO
DITI YES
TRNX YES
EXTT YES
FTOP FRES
VNR NO
NIT 8
NAS_ATCL YES
NAS_ACTV NO
FOPT 0
CNTC
NATC
INTC

 

[RickyPone]

Can you post the route and a phone tn?

 

[pbxn]

Not going to Nortel phone. Its dumping to audiocode gw, to another pbx, here's the route though. Thanks
TYPE RDB
CUST 00
ROUT 35
DES I3
TKTP TIE
M911P NO
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC ISGF
SBN NO
PNI 00001
NCNA NO
NCRD NO
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
CPFXS YES
DAPC NO
INTC NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 2035
TCPP NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096


PAGE 002


IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS NO
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO

 

[RickyPone]

So you are sending incoming did to audiocodes via route 35 and cdp?

 

[pbxn]

Yep. Going to test another flavor of qsig to see if that works. Will post back if it does in fact work. Thanks

 

[pbxn]

Well tried ESGF instead of ISGF with no luck. If I route via CDP, DSC, FLEN anything, 4 digit dial works between Nortel and other PBX works fine, I get fast busy when dialing from outside in 9+.

 

[RickyPone]

When dialing outside in are you using a phone on the cs1000? If so post the tn. I would assume it doesn't work if you use a cellphone or some other phone not on the switch.

 

[pbxn]

Tried all the standards, Nortel onsite switch, Nortel off site switch, cell. I must of configured this thing 10 times and changed endless prompts. This switch was purchased from another company and not real sure how they got stuff to work. FRL set to 0 made this work. I tried every number from 1-7, flipped NCOS around abit on sets and trunks, but 0 is the key on this lovely switch. Thanks for the posts

 

[RickyPone]

So you can call switch to switch via four digit? Which means the problem is from incoming route to tie? If so post the incoming route.