CRMN001 High call reg usage - ALARM.

[bungy43uk]

Every 15 mins or so Im getting the following alarm:

CRMN001 HIGH Call Reg Usage, Pcnt Used=92, Num Used=608
NumCR=655

Error suggests I increase the number of CRs which requires an INIT.

Firstly, how do I check what current setting is....secondly how do I increase and thirdly what do I do if its already maxed out...?

Any help would be much appreciated as im already up to 92 percent and incresing every 15 mins.

Bungy

 

[yyrkroon]

ld 22

req=prt
type = parm and look at the NCR prompt, it set to 655 now, change it to anything between 1000 to 25000 or if you really want to do this properly, review the capicity engineering ntp for the correct amount

 

[Wane47]

you can print them out in ld 22. The type is parm (parmeters), the prompt you are looking for is ncr. There should be a value after it. that would be the number of call registers that are assigned.

To change that value you go to ld 17. However what that value would be is determined by system type and software release.

You need to go to ld 22 and print the iss and your current parms and post them here.

 

[bungy43uk]

Wane47 - thank you, herewith the requested data:

prt
TYPE parm

PARM
LPIB 2000
HPIB 2000
500B 100
SL1B 160
DTIB 70
DTOB 35
NCR 655
MGCR 25
NCPU 2
CFWS NO
PCML A
ALRM YES
ERRM ERR BUG AUD
DTRB 100
ABCD NO
TMRK 128
FCDR NEW
PCDR YES
TPO YES
TSO NO
CLID YES
DUR5 NO
MLDN YES
MARP YES
IPIE NO
FRPT NEFR
DCUS NULL
DTDT NO
MSCL 6001
PMSI
MANU PMS1
PMCR 0
PORT NONE
NDIS 20
OCAC NO
MTRO PPM
SBA_ADM_INS 000
SBA_USER 512
BCAP SPEECH
IDLE_SET_DISPLAY Astrium Portsmouth
ICON NO
MSEC ON
MSSD MSNV
NKEY 31
TKEY 24

REQ iss

VERSION 3621
RELEASE 5
ISSUE 00 W +
IDLE_SET_DISPLAY Astrium Portsmouth

 

[bungy43uk]

Im currently trawling thru the NTP's to find out if I can increase from 655 but dont seem to be able to find what im looking for - can anyone help please or give me the ref within the NTP ie NN43001-*** ETC

Im running at 97 percent at the moment and about to loose my CDR capabilities etc.....so I need to do something abut this ASAP !!

 

[yyrkroon]

VERSION 3621
81C with P4 processor or a CS1000MG with P4 processor, it's safe to set NCR to 20000 and ini....why on earth it was set to 655 is beyond....

 

[yyrkroon]

don't forget to ini for the changes to take effect, the ini will also resolve your CR issue, or when it reaches 100% it will ini on its own anyway.

 

[johnpoole]

my 81 is pushing high to med usage stations.(hospital)

  LPIB 3500
  HPIB 3500
  500B 1000
  SL1B 255
  NCR  20000
  MGCR 25
  CSQI 2500
  CSQO 2500
  TUBO NO
  NCPU 2
  CFWS YES
  PCML MU
  ALRM YES
  ERRM ERR BUG AUD
  DTRB 100
  TMRK 128
  FCDR OLD
  PCDR NO
  TPO  NO
  TSO  NO
  CLID YES
  DUR5 NO
  MLDN YES
  MARP YES
  IPIE NO
  FRPT NEFR
  DCUS NULL
  MSCL 255
  PMSI
    MANU PMS1
    PMCR 60
    PORT NONE
  NDIS 20
  OCAC NO
  MTRO MR
  SBA_ADM_INS 002
  SBA_USER 050
  BCAP SPEECH
  IDLE_SET_DISPLAY Palmetto Health
  ICON YES
  MSEC ON
    MSSD MSNV
    NKEY 31
    TKEY 24

john poole
bellsouth business
columbia,sc

 

[bungy43uk]

Thank you all for your input, I have reset my PARM's to:

LPIB 3500
HPIB 3500
NCR 20000

Currently running at 94 pct and seeing the occasional string of FIJI037 alarms too which might suggest the switch is running very tight on resources. INIT not practical at present but if 100pct used then changes will take effect anyway otherwise if I escape today without a crash I will INIT this evening.

Thanks again
Bungy