Cot card and a Premicell 3

[3Sixty]

Hi Guys

I am not sure if anyone can help me with this. I have installed a cot card and a device called a premicell. The premicell is a mobile phone in a box with an analogue line or analogue extension connection. I have programmed the cot card as a standard analogue line. The customer wants all 07 numbers to go out via the premicell. I have programme the RDB and created the trunks on the card. I have set up a RLI and DMI and associated the SPN 07 with the RLI,DMI etc.

If I make a call out the trunk goes busy and the premicell goes busy but the call returns NU tone. I have tested the premicell by plugging a test phone on the krone connection were the premicell is connected to the cot card and I can make a call out on the premicell. I am wondering is it some sort of timer issues with the third party box.

Any help appreciated

Marshall

http://www.nortelsupport.net

 

[dlesap]

I have that kind of device but with ISDN BRI connection.
For your problem, is overlap signaling engaged in RLI conf?
I mean your SPN must have the FLEN value with the right number of digits. Then the number will be send in block to the COT

 

[johnpoole]

strange that the provider wants a cot connection as opposed to an analog station.. normal key system from a line side or to a trunk card would usually be a station card on the pbx side..

john poole
bellsouth business
columbia,sc

 

[GHTROUT]

If you can connect a phone to the box, as if you were the Meridian, and it works when you lift the handset and dial, then you know it can work on the Meridian as a Loop Start Trunk

Youe first test is 'not' with BARS and DMI and SPNs - it is "can you dial the ACCD - Trunk Route Access Code and make a good call"

If not, your Route or Trunk TN prog is wrong

If Yes, your BARS is wrong



~

http://www.GHTROUT.com/

 

[3Sixty]

Hi Guys

I have had a look and I can not dial the access code to get out on the trunks.I have listed the RDB and the trunks any help would be appreciated.

RDB

TYPE RDB
CUST 00
DMOD
ROUT 111
DES PREMICELL
TKTP COT
NPID_TBL_NUM 0
PRIV NO
RPA NO
SAT NO
IDEF NET
RCLS EXT
DTRK NO
ISDN NO
PTYP ACO
AUTO NO
ICOG IAO
RANX NO
SRCH LIN
TRMB NO
STEP 110
ACOD 1611
TARG 01
BILN NO
OABS
TIMR ICF 384
OGF 384
EOD 13952
LCT 128
DSI 60032
NRD 10112
DDL 70
ODT 4096
RGV 256
FLH 510
GTO 2944
GTI 2944
ARP 3
SFB 3
CRD 512
IENB 5
TFD 0
LEXT 100
VGD 6
SST 3 0
DTD NO
SCDT NO
2 DT NO
NEDC ETH
FEDC ETH
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
DDO NO
DRNG NO
CDR NO
CCO NO
NATL YES
SSL


PAGE 002

CFWR NO
IDOP NO
MUS NO
MR NO
PANS YES
RACD NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
OHTD NO
PLEV 2
OPR NO
RCAL NO
MCTS NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 1611 111
SGRP 0
AACR NO

Trk Info
TN 006 0 00 00
TYPE COT
CUST 0
XTRK XCOT
FWTM NO
BIMP 600
TRK ANLG
NCOS 0
RTMB 111 1
NITE 2366
SIGL LDC
SUPN YES
AST NO
IAPG 0
BTID 0
CLS UNR DIP CND WTA LPR APN THFD BARD
P10 LOL
TKID 1
DATE 29 MAY 2006

http://www.nortelsupport.net

 

[3Sixty]

Sorry forgot to say the trunks work fine for incoming calls. Just not outgoing.

Here is the acod in LD 20.

DN 1611
TYPE RDB
ROUT 111

Thanks again

Marshall

http://www.nortelsupport.net

 

[acewarlock]

CLS DTN

 

[GHTROUT]

On your phone TGAR 0 - if it is currenty TGAR 1, that is the problem

Also Try LD14 - SIGL LOP if that is an option on your version

~

http://www.GHTROUT.com/

 

[johnpoole]

ld 16
chg
rdb
111
targ x1..

always remove the default targ, unless you don't plan on giving access to that route. the default tgar and the default targ are one.. i always x1 on the original install. saves a headache


john poole
bellsouth business
columbia,sc

 

[3Sixty]

Not to be a pain about this but if it is the TGAR as you have suggested John would the call even reach the card. If I stat the card during a call I can see the trunk go busy and the GSM bridge get accessed.

Just curious

Marshall

http://www.nortelsupport.net

 

[3Sixty]

I have got this working. Turns out the contractor installing the premicell had provided the wrong box.

Marshall

Thanks for all the replies

http://www.nortelsupport.net