CLID over IP Trunk between sites

[scottvtr]

We have a number of remote sites (BCM\SRG) connected to our main site via IP Virtual Trunks. Calls route fine and the internal calling line ID is correct (ie. Internal Name and ext. number appears fine).
However, when an external caller dials the DID number of a person at a remote site, all they get is the ACOD appear on their set so they can't identify the callers.
The calls route fine.

Here is the RDB for the IP Trunk route:

TYPE RDB
CUST 00
ROUT 20
DES IPROUTE
TKTP TIE
NPID_TBL_NUM 0
ESN NO
RPA NO
CNVT NO
SAT NO
RCLS INT
VTRK YES
ZONE 001
PCID H323
CRID NO
NODE 1231
DTRK NO
ISDN YES
MODE ISLD
DCH 20
IFC SL1
PNI 00001
NCNA YES
NCRD YES
TRO NO
FALT NO
CTYP CDP
INAC NO
ISAR NO
DAPC NO
PTYP ATT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 1520
TCPP NO
TARG
CLEN 10
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
SIGO STD
STYP SDAT
MFC NO
ICIS YES
OGIS YES
TIMR ICF 1920
OGF 1920
EOD 13952
LCT 256
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896
SFB 3
PRPS 800
NBS 2048
NBL 4096
IENB 5
TFD 0
VSS 0
VGD 6
EESD 1024
SST 5 0
DTD NO
SCDT NO
2 DT NO
NEDC ORG
FEDC ORG
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR YES
INC YES
LAST YES
TTA YES
ABAN YES
CDRB NO
QREC YES
OAL YES
AIA NO
OAN YES
OPD NO
NDP EXC 0
CDRX NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS NO
PANS YES
RACD NO
MANO NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
OPR NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 1520 20
ATRR NO
TRRL NO
SGRP 0
AACR NO


Cheers guys.

 

[johnpoole]

do that in the rcap of the dch

john poole
bellsouth business
columbia,sc

 

[johnpoole]

PNI 00001
that pni also needs to be in both cdb's and on the far end route, mark both routes as internal max out the rcap and you will get ld 95 names and dn's to a nortel or if you run qsig, any other switch.. i've seen that work between nortel and cisco/rolm/mitel etc

john poole
bellsouth business
columbia,sc

 

[scottvtr]

Thanks John,

I get LD95 names appearing on the IP sets at the remote sites but just not external DID numbers? A copy of my D-Channels settings are below:

ADAN DCH 20
CTYP DCIP
DES Vtrk
USR ISLD
ISLM 4000
SSRC 1800
OTBF 32
NASA YES
IFC SL1
CNEG 1
RLS ID 4
RCAP ND2 NCT RVQ TAT
MBGA NO
H323
OVLR NO
OVLS NO

 

[NARSBARS]

I am trying to send CLID to a BCM50. All I get is the last 4 digits of the extension.

Here is a post of the RDB for the IP route. Any help greatly appreciated.

ROUT 10


TYPE RDB
CUST 00
ROUT 10
DES IPROUTE
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS INT
VTRK YES
ZONE 000
PCID H323
NODE 2222
DTRK NO
ISDN YES
MODE ISLD
DCH 10
IFC SL1
PNI 00001
NCNA YES
NCRD YES
TRO NO
FALT NO
CTYP UKWN
INAC NO
ISAR NO
DAPC NO
PTYP ATT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 701
TCPP NO
TARG 01
CLEN 16
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
STYP SDAT
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096


PAGE 002


IENB 5
TFD 0
VSS 0
VGD 6
SST 5 0
NEDC ORG
FEDC ORG
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR NO
VRAT NO
MUS NO
MANO NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO

NARSBARS