CLID OUTBOUND ISSUE 1

[steeviedude]

Hello,
Any advice on how to proceed with resolving folowing issue appreciated..
Have a site with CLI table 0 set to send out 02555555718.
CLI 1 set to send out callers DN 57xx.
The ISDN30 was set to send default of 5710 if it does not recognise CLI being sent at time of testing.
Issue is that some calls when received display the default number even though a DCH trace shows it sending calling number as the CLID 2555555718.
ISDN30 supplier has tested with analyser and not seen issue with outbound cli being received so its all pointing back to the switch.
Switch is CS1K R5.5.
I have tested using same handset and dialling my mobile.
3 out of the 90+ calls were received with the default cli
of 5710. My DCH trace showed same number being sent out each time see below for good/bad trace.
ISDN30 has apparently had the presentation number amended to xx5718 but some calls still show as 5710?
Stumped.....

*********CALL FROM 5897 to MOBILE**********************************
**********CLI RECEIVED OK 02055555718******************************


DCH 10 UIPE_OMSG CC_SETUP_REQ REF 0000223D CH 110 8 TOD 17:01:54 CK 937C6A0A
PROGRESS: ORIGINATING END IS NOT ISDN
CALLING #:2055555718 NUM PLAN: E164 TON: NATL
CALLED #:07555555150 NUM PLAN: E164 TON: UNKNOWN
DCH 10 UIPE_IMSG CC_PROCEED_IND REF 0000223D CH 110 8 TOD 17:01:54 CK 937C6C51
DCH 10 UIPE_IMSG CC_ALERT_IND REF 0000223D CH 110 8 TOD 17:02:00 CK 937CA3AD
DCH 10 UIPE_IMSG CC_SETUP_CONF REF 0000223D CH 110 8 TOD 17:02:06 CK 937CC73D
CONNECT #:NO DIGIT NUM PLAN: UNKNOWN TON: UNKNOWN

trac 0 5897 ACTIVE TN 000 1 02 01 IPMG 000 1
ORIG TN 000 1 02 01 IPMG 000 1 KEY 0 SCR MARP CUST 0 DN 5897 TYPE 3904
VGW TN 000 1 00 08
MEDIA ENDPOINT IP: 1&&.18.43.6 PORT: 5216
TERM TN 110 08 IPMG 000 0 V PHYSICAL TN 000 0 00 01 TIE RMBR 10 8 OUTGOING TRUNK CALL
DIAL DN 307555555150
MAIN_PM ESTD
TALKSLOT ORIG 75 TERM 11 JUNCTOR ORIG0 TERM0
EES_DATA:
NONE
QUEU NONE
CALL ID 0 14003

---- ISDN PRA CALL (TERM) ----
CALL REF # = 8765
BEARER CAP = VOICE
HLC =
CALL STATE = 10 ACTIVE
CALLING NO = 2055555718 NUM_PLAN:E164 TON:NATIONAL ESN:NPA
CALLED NO = 07555555150 NUM_PLAN:E164 TON:UNKNOWN ESN:UNKNOWN

.
DCH 10 UIPE_IMSG CC_DISC_IND REF 0000223D CH 110 8 TOD 17:02:28 CK 937D7818
CAUSE: #16 - NORMAL CALL CLEARING
PROGRESS: INBAND INFO OR PATTERN IS AVAIL

DCH 10 UIPE_OMSG CC_RELEASE_REQ REF 0000223D CH 110 8 TOD 17:02:30 CK 937D8458


*********CALL FROM 5897 to MOBILE**********************************
**********CLI RECEIVED DEFAULT 02055555710******************************

DCH 10 UIPE_OMSG CC_SETUP_REQ REF 00002249 CH 110 26 TOD 17:08:41 CK 9388E40A
PROGRESS: ORIGINATING END IS NOT ISDN
CALLING #:2055555718 NUM PLAN: E164 TON: NATL
CALLED #:07555555150 NUM PLAN: E164 TON: UNKNOWN

DCH 10 UIPE_IMSG CC_PROCEED_IND REF 00002249 CH 110 26 TOD 17:08:41 CK 9388E673

DCH 10 UIPE_IMSG CC_ALERT_IND REF 00002249 CH 110 26 TOD 17:08:49 CK 93891EC6
PROGRESS: TERMINATING END IS NOT ISDN

DCH 10 UIPE_IMSG CC_SETUP_CONF REF 00002249 CH 110 26 TOD 17:08:55 CK 93894CB1
CONNECT #:NO DIGIT NUM PLAN: UNKNOWN TON: UNKNOWN



.trac 0 5897


ACTIVE TN 000 1 02 01 IPMG 000 1

ORIG TN 000 1 02 01 IPMG 000 1 KEY 0 SCR MARP CUST 0 DN 5897 TYPE 3904
VGW TN 000 1 00 12

MEDIA ENDPOINT IP: 1&&.18.43.6 PORT: 5224
TERM TN 110 26 IPMG 000 0 V PHYSICAL TN 000 0 00 01 TIE RMBR 10 26 OUTGOING TRUNK CALL
DIAL DN 307555555150
MAIN_PM ESTD
TALKSLOT ORIG 69 TERM 5 JUNCTOR ORIG0 TERM0
EES_DATA:
NONE
QUEU NONE
CALL ID 0 13990


---- ISDN PRA CALL (TERM) ----
CALL REF # = 8777
BEARER CAP = VOICE
HLC =
CALL STATE = 10 ACTIVE
CALLING NO = 2055555718 NUM_PLAN:E164 TON:NATIONAL ESN:NPA
CALLED NO = 07555555150 NUM_PLAN:E164 TON:UNKNOWN ESN:UNKNOWN



.


.trad 110 26


ACTIVE TN 110 26 IPMG 000 0

ORIG TN 000 1 02 01 IPMG 000 1 KEY 0 SCR MARP CUST 0 DN 5897 TYPE 3904
VGW TN 000 1 00 12

MEDIA ENDPOINT IP: 1&&.18.43.6 PORT: 5224
TERM TN 110 26 IPMG 000 0 V PHYSICAL TN 000 0 00 01 TIE RMBR 10 26 OUTGOING TRUNK CALL
DIAL DN 307555555150
MAIN_PM ESTD
TALKSLOT ORIG 69 TERM 5 JUNCTOR ORIG0 TERM0
EES_DATA:
NONE
QUEU NONE
CALL ID 0 13990


---- ISDN PRA CALL (TERM) ----
CALL REF # = 8777
BEARER CAP = VOICE
HLC =
CALL STATE = 10 ACTIVE
CALLING NO = 2055555718 NUM_PLAN:E164 TON:NATIONAL ESN:NPA
CALLED NO = 07555555150 NUM_PLAN:E164 TON:UNKNOWN ESN:UNKNOWN



.

DCH 10 UIPE_IMSG CC_DISC_IND REF 00002249 CH 110 26 TOD 17:10:41 CK 938C91BF
CAUSE: #31 - NORMAL UNSPECIFIED
PROGRESS: INBAND INFO OR PATTERN IS AVAIL

DCH 10 UIPE_OMSG CC_RELEASE_REQ REF 00002249 CH 110 26 TOD 17:10:43 CK 938C9DF6
CAUSE: #16 - NORMAL CALL CLEARING


DCH 10 UIPE_IMSG CC_RELEASE_CONF REF 00002249 CH 110 26 TOD 17:10:43 CK 938C9E9F

 

[Firebird Scrambler]

Just to recap on this,

CLID 0 is set to allow any sets (Non DDI to call 02555555718) as long as "0" is entered against that DN

CLID 1 is configured to allow the DID number to be displayed at the callers end, again as long as the entry of "1" was entered against the DID DN?.

I'm puzzled on the 5710 number. I'm assuming that this number is within your DID range?.

Is CLID 0 set to DIDN = NO and CLID 1 set to DIDN = YES?.

Sorry if I'm misreading your thread.

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[steeviedude]

Sir

You have read my elongated version correctly...

5710 is the main number on the incoming ISDN30 BT bearer.
It has also unfortunately been given to the companies CEO, bad choice I know but this fault is my first dealings with company, prior to this all set up was done by the companies telco team in Asia.

Extra issue is that they remotely changed AC1 from 9 to 3, to accomodate 9xxx ddi range, but 9xx etc still works outbound.

 

[steeviedude]

Is CLID 0 set to DIDN = NO and CLID 1 set to DIDN = YES?.

Entry 0
HNTN 20
ESA_APDN No
HLCL 55555718
DIDN No
Class_FMt DN

Entry 1
HNTN 20
ESA_APDN yes
HLCL 55
DIDN No
Class_FMt DN

 

[Firebird Scrambler]

I'm a little out of touch with the CLID tables, but I think the DDI CLID 1 needs to have DIDN = YES

In the UK, we have problems trying to get the DID or DDI to work because the numbering range starts with a "0". It's a game of trying to alter some of the full outgoing digits dialled e.g.

As you have a BT circuit, there is the additional problem of the type of exchange that the bearer is connected with as it's usually System X "Plessey" or System "Y" Ericson. The reason is that one needs "0" removed. Also, it's woth checking if the customer has paid for outgoing CLID to be sent out etc.

The details below are very old and from a guide I did when I was at BT many moons ago.



SETTING UP CLID ON EURO ISDN ROUTES
******* ** **** ** **** **** ******

** WARNING THERE IS DIFFERENCES BETWEEN SYSTEM X AND SYSTEM Y EXCHANGES **
** WHICH MAY CAUSE DIFFICULTIES i.e SYSTEM Y DOES'NT LIKE THE INITIAL 0 **
** THEREFORE HNTN WILL HAVE TO BE 1823 FOR EXAMPLE. **

** ALSO SYSTEM Y NEEDS TO SEE AT LEAST 8 INITIAL DIGITS TO RECOGNISE CLI **
** THEREFORE WITH HNTN - 1823 HLCL - 3455 FOR EXAMPLE. **


REQ: CHG
TYPE: NET

TYPE NET_DATA
CUST 0
OPT
AC2
FNP
CLID YES
SIZE 256 (DEFAULT SETTING)
INTL 44 (UK INTERNATIONAL CODE)
ENTRY 0 )
HNTN 01823 )
HLCL 34 ) FOR KEY DDI No (i.e 01823 34 5500)
DIDN YES )
HLOC )
LSC )
ENTRY 0 SAVED!
ENTRY 1 )
HNTN 01823 )
HLCL 326800 ) FOR ANOTHER No TO BE SENT (i.e 01823 326800)
DIDN NO )
HLOC )
LSC )
ENTRY 1 SAVED!
ENTRY 2 )
HNTN )
HLCL ) FOR HOME LOCATION CODE TO BE SENT ON PRIVATE NETWORKS
DIDN ) WITH KEY No (i.e 123 5500)
HLOC 123 )
LSC )
ENTRY 2 SAVED!
ENTRY 3 )
HNTN )
HLCL ) FOR LOCAL STEERING CODE WITH KEY No (i.e 456 5500)
DIDN )
HLOC )
LSC 456 )
ENTRY 3 SAVED!
ENTRY
ISDN
PNI
PINX_DN
MBG
BSGC
PFX1
PFX2
HLOC
LSC
RCNT
PSTN
TNDM
PCMC
SATD
OCLI
TIDM
DASC
ROPT
DITI
TRNX
EXTT
FTOP
APAD
VNR
NIT
NAS ATCL
NAS ACTV
FOPT
CNDN
CNAT
CNIP

>LD 21

REQ: PRT
TYPE: CLID
CUST 0
SIZE 256
RNGE

INTL 44

ENTRY 0
HNTN 01823
HLCL 34
DIDN YES
HLOC
LSC

ENTRY 1
HNTN 01823
HLCL 326800
DIDN NO
HLOC
LSC

ENTRY 2
HNTN
HLCL
DIDN YES
HLOC 123
LSC

ENTRY 3
HNTN
HLCL
DIDN YES
HLOC
LSC 456

ASSIGNING TO AN ANALOGUE SET
********* ** ** ******** ***

CLID TABLE 0 IS ALLOCATED TO ALL SETS BY DEFAULT

LD 10
REQ CHG
TYPE: 500
TN 4 0 7 0
ECHG YES
ITEM DN 2001 1
MARP
CPND
VMB
ITEM

REQ: PRT
TYPE: 500
TN 4 0 7 0
DATE
PAGE
DES

DES FAX
TN 004 0 07 00
TYPE 500
CDEN 4D
CUST 0
WRLS NO
DN 2001 1 MARP (NOTE CLID TABLE 1 FOLLOWING DN No)
CPND
CPND_LANG ROMAN (NAME IS NOT LOST WHEN CLID TABLE IS CHANGED)
NAME MODEM /FAX
XPLN 27
DISPLAY_FMT FIRST,LAST
AST NO
IAPG 0
HUNT 2001
TGAR 1
LDN NO
NCOS 5
SGRP 0
RNPG 0
LNRS 16
XLST
SCI 0
SCPW 2001
SFLT NO
CAC_MFC 0
CLS TLD DTN FBD XFA WTA THFD FNA HTA ONS
LPR XRA AGRD CWD SWD MWD RMMD SMWD LPD XHD CCSD LNA TVD
CFTA SFA MRD C6A CNID CLBD AUTU
ICDD CDMD EHTD MCTD
GPUD DPUD CFXD ARHA OVDD AGTD CLTD LDTD ASCD
MBXD UDI RCC HBTA IRGD IAMD DDGA NAMA MIND
NRWD NRCD NROD CRD PRSD MCRD
EXR0 SHL SMSD ABDD CFHD DNDY DNO3
CWND USRA BNRD OCBD RTDD RBDD RBHD FAXD PGND FTTC
RCO 0

ASSIGNING TO A DIGITAL SET
********* ** * ******* ***

LD 11
REQ: PRT
TYPE:
TYPE 3904
TN 12 0 2 5
DATE
PAGE
DES

DES CUSSRV
TN 012 0 02 05
TYPE 3904
CDEN 8D
CTYP XDLC
CUST 0

KEY 00 SCR 2227 0 MARP
CPND
CPND_LANG ROMAN
NAME PHIL GRAND (NOTE KEYS 0 & 1 ALLOCATED TO CLID 0)
XPLN 27
DISPLAY_FMT FIRST,LAST
01 SCR 2200 0 MARP
02 DSP
03 RDL 16
04 RDL 16
05 RDL 16
06 ADL 16
07 ADL 16
08 ADL 16
09 ADL 16
10 ADL 16
11 ADL 16

REQ: CHG
TYPE:
TYPE 3904
TN 12 0 2 5
ECHG YES
ITEM KEY 1 SCR 2200 1
MARP
CPND
VMB
KEY
ITEM



All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[steeviedude]

Sorry that was a typo
DIDN = YES on CLID 1

Issue is that on CLID 0 it works ok 90% of time but even using same handset dialling out over same route on same link it returns the ISDN default number 10% of time.