Cisco 857 DSL issues

[danfranklin]

I am having issues with layer one on the ATM 0 interface. Currently the interface is line down and protocol down when I connect them in the office. When I connect the routers to my ADSL at home they work fine. This was leading me to a fault on the ADSL line in the office. So called BT. they sent an engineer to site and the line tested o.k. I connected our ADSL modem and this also worked. I connected a Cisco 827 and this also worked. Has anyone else had this issue?

ATM Config

interface ATM0
no ip address
no ip mroute-cache
atm vc-per-vp 64
no atm ilmi-keepalive
q
pvc 0/38
encapsulation aal5mux ppp dialer
dialer pool-member 1


here is the debug from atm events

ar 2 21:28:35.575: ATM0 atmsar_update_us_bandwidth(): upstream bw =4608 Kbps
*Mar 2 21:28:36.071: (ATM0)1a_enable: delay activation of vcd=1, vc=0x827E7638
*Mar 2 21:28:36.071: DSL: SM: [DMTDSL_STOP -> DMTDSL_INIT]
*Mar 2 21:28:36.147: DSL: SM: [DMTDSL_INIT -> DMTDSL_DLOAD_1]
*Mar 2 21:28:36.147: DSL: Downloading init_AMR-R-2.5.011_no_bist.bin
*Mar 2 21:28:36.151: DSLATM0) Downloaded 2 blocks... Finished!
*Mar 2 21:28:36.151: DSL(ATM0): Sent command 0x14
*Mar 2 21:28:37.575: %LINK-3-UPDOWN: Interface ATM0, changed state to down
*Mar 2 21:28:37.575: atmsar_atm_lineaction(ATM0): state=0
*Mar 2 21:28:38.151: DSL: Received response: 0x80
*Mar 2 21:28:38.151: DSL: SM: [DMTDSL_DLOAD_1 -> DMTDSL_DLOAD_2]
*Mar 2 21:28:38.151: DSL: Downloading AMR-R-2.5.011.bin
*Mar 2 21:28:38.183: DSL(ATM0): Downloaded 100 blocks
*Mar 2 21:28:38.215: DSL(ATM0): Downloaded 200 blocks
*Mar 2 21:28:38.247: DSL(ATM0): Downloaded 300 blocks
*Mar 2 21:28:38.279: DSL(ATM0): Downloaded 400 blocks
*Mar 2 21:28:38.311: DSL(ATM0): Downloaded 500 blocks
*Mar 2 21:28:38.343: DSL(ATM0): Downloaded 600 blocks
*Mar 2 21:28:38.379: DSL(ATM0): Downloaded 700 blocks
*Mar 2 21:28:38.411: DSL(ATM0): Downloaded 800 blocks
*Mar 2 21:28:38.443: DSL(ATM0): Downloaded 900 blocks
*Mar 2 21:28:38.471: DSL(ATM0): Downloaded 1000 blocks
*Mar 2 21:28:38.503: DSL(ATM0): Downloaded 1100 blocks
*Mar 2 21:28:38.535: DSL(ATM0): Downloaded 1200 blocks
*Mar 2 21:28:38.571: DSL(ATM0): Downloaded 1300 blocks
*Mar 2 21:28:38.603: DSL(ATM0): Downloaded 1400 blocks
*Mar 2 21:28:38.635: DSL(ATM0): Downloaded 1500 blocks
*Mar 2 21:28:38.667: DSL(ATM0): Downloaded 1600 blocks
*Mar 2 21:28:38.695: DSL(ATM0): Downloaded 1700 blocks
*Mar 2 21:28:38.727: DSL(ATM0): Downloaded 1800 blocks
*Mar 2 21:28:38.763: DSL(ATM0): Downloaded 1900 blocks
*Mar 2 21:28:38.795: DSL(ATM0): Downloaded 2000 blocks
*Mar 2 21:28:38.827: DSL(ATM0): Downloaded 2100 blocks
*Mar 2 21:28:38.859: DSL(ATM0): Downloaded 2200 blocks
*Mar 2 21:28:38.891: DSL(ATM0): Downloaded 2300 blocks
*Mar 2 21:28:38.919: DSL(ATM0): Downloaded 2400 blocks
*Mar 2 21:28:38.955: DSL(ATM0): Downloaded 2500 blocks
*Mar 2 21:28:38.987: DSL(ATM0): Downloaded 2600 blocks
*Mar 2 21:28:39.019: DSL(ATM0): Downloaded 2700 blocks
*Mar 2 21:28:39.051: DSL(ATM0): Downloaded 2800 blocks
*Mar 2 21:28:39.083: DSL(ATM0): Downloaded 2900 blocks
*Mar 2 21:28:39.115: DSL(ATM0): Downloaded 3000 blocks
*Mar 2 21:28:39.147: DSL(ATM0): Downloaded 3100 blocks
*Mar 2 21:28:39.183: DSL(ATM0): Downloaded 3200 blocks
*Mar 2 21:28:39.215: DSL(ATM0): Downloaded 3300 blocks
*Mar 2 21:28:39.243: DSL(ATM0): Downloaded 3400 blocks
*Mar 2 21:28:39.275: DSL(ATM0): Downloaded 3500 blocks
*Mar 2 21:28:39.307: DSL(ATM0): Downloaded 3600 blocks
*Mar 2 21:28:39.339: DSL(ATM0): Downloaded 3700 blocks
*Mar 2 21:28:39.375: DSL(ATM0): Downloaded 3800 blocks
*Mar 2 21:28:39.391: DSLATM0) Downloaded 3850 blocks... Finished!
*Mar 2 21:28:39.391: DSL(ATM0): Sent command 0x14
*Mar 2 21:28:41.391: set tx_gain_offset to 0
*Mar 2 21:28:41.391: set rx_gain_offset to 0
*Mar 2 21:28:41.391: set target_noise_margin_offset to 0
*Mar 2 21:28:41.391: set max_bits_tone_limit to 15
*Mar 2 21:28:41.391: changed current state to do open!!
*Mar 2 21:28:41.391: DSL: SM: [DMTDSL_DLOAD_2 -> DMTDSL_DO_OPEN]
*Mar 2 21:28:41.391: DSL: Send ADSL_OPEN command.
*Mar 2 21:28:41.391: DSL(ATM0): Using subfunction 0x0
*Mar 2 21:28:41.391: LOCAL:Max noise margin for power cutoff 31
*Mar 2 21:28:41.391: DSL(ATM0): Sent command 0x3
*Mar 2 21:28:43.891: DSL(ATM0): 1: Modem state = 0x9
*Mar 2 21:28:46.391: DSL(ATM0): 2: Modem state = 0x10
*Mar 2 21:28:48.891: DSL(ATM0): 3: Modem state = 0x10
*Mar 2 21:28:51.391: DSL(ATM0): 4: Modem state = 0x10
*Mar 2 21:28:52.411: DSL: Received response: 0x22
*Mar 2 21:28:52.411: DSL: Open failed: Error in early non-CRC message or in fir
st CRC-covered message -- retrying
*Mar 2 21:28:52.411: sleep 5 seconds
*Mar 2 21:28:57.411: DSL: Send ADSL_OPEN command.
*Mar 2 21:28:57.411: DSL(ATM0): Using subfunction 0x0
*Mar 2 21:28:57.411: LOCAL:Max noise margin for power cutoff 31
*Mar 2 21:28:57.411: DSL(ATM0): Sent command 0x3
*Mar 2 21:28:59.911: DSL(ATM0): 1: Modem state = 0x9
*Mar 2 21:29:02.411: DSL(ATM0): 2: Modem state = 0x10
*Mar 2 21:29:04.911: DSL(ATM0): 3: Modem state = 0x10
*Mar 2 21:29:07.411: DSL(ATM0): 4: Modem state = 0x10
*Mar 2 21:29:08.495: DSL: Received response: 0x22
*Mar 2 21:29:08.495: DSL: Open failed: Error in early non-CRC message or in fir
st CRC-covered message -- retrying
*Mar 2 21:29:08.495: sleep 5 seconds
*Mar 2 21:29:13.495: DSL: Send ADSL_OPEN command.
*Mar 2 21:29:13.495: DSL(ATM0): Using subfunction 0x0
*Mar 2 21:29:13.495: LOCAL:Max noise margin for power cutoff 31
*Mar 2 21:29:13.495: DSL(ATM0): Sent command 0x3
*Mar 2 21:29:15.995: DSL(ATM0): 1: Modem state = 0x9
*Mar 2 21:29:18.495: DSL(ATM0): 2: Modem state = 0x10
Router(config-if)#
*Mar 2 21:29:20.995: DSL(ATM0): 3: Modem state = 0x10
*Mar 2 21:29:23.495: DSL(ATM0): 4: Modem state = 0x10
*Mar 2 21:29:24.563: DSL: Received response: 0x22
*Mar 2 21:29:24.567: DSL: Open failed: Error in early non-CRC message or in fir
st CRC-covered message -- retrying

 

[danfranklin]

I have found the answer. If anyone is interested which I think you should be look at:

http://forum.cisco.com/eforum/servl...md=MB?cmd=display_location&location=.1dd8e636