Cisco 7206

[NewToo]

Hello,

I'm new at cisco, but here is my issue. I have a Cisco 7206 that i'm try to put an FastEthernet port in a speed of 10mbp but the router would not allow me to. It seem like there is not command for speed 10. Here is the IOS i'm running. Any help would be great.


IOS (tm) 7200 Software (C7200-JS-M), Version 12.2(3), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Wed 18-Jul-01 10:50 by pwade
Image text-base: 0x600089C0, data-base: 0x61704000

ROM: System Bootstrap, Version 11.1(13)CA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
BOOTLDR: 7200 Software (C7200-BOOT-M), Version 12.0(22)S, EARLY DEPLOYMENT RELEASE SOFTWARE (fc2)

Core uptime is 11 weeks, 3 days, 50 minutes
System returned to ROM by power-on
System image file is "slot0:c7200-js-mz.122-3.bin"

 

[IPKONFIG]

You should be able to set the speed and duplex of a Fast Ethernet port. Why don't you post the rest of the "show version" and we can see what kind of PA you have or what interfaces you are working with. Are you sure it's Fast Ethernet and not just Ethernet?

"I can picture a world without war. A world without hate. A world without fear. And I can picture us attacking that world, because they'd never expect it."
- Jack Handey, Deep Thoughts

 

[NewToo]

IPKONFIG

Here is the reset of the show ver.

Core#sh ver
Cisco Internetwork Operating System Software
IOS (tm) 7200 Software (C7200-JS-M), Version 12.2(3), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Wed 18-Jul-01 10:50 by pwade
Image text-base: 0x600089C0, data-base: 0x61704000

ROM: System Bootstrap, Version 11.1(13)CA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
BOOTLDR: 7200 Software (C7200-BOOT-M), Version 12.0(22)S, EARLY DEPLOYMENT RELEASE SOFTWARE (fc2)

Core uptime is 11 weeks, 5 days, 23 hours, 32 minutes
System returned to ROM by power-on
System image file is "slot0:c7200-js-mz.122-3.bin"

cisco 7206 (NPE200) processor (revision B) with 114688K/16384K bytes of memory.
Processor board ID 8085288
R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache
6 slot midplane, Version 1.3

Last reset from power-on
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
2 FastEthernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
125K bytes of non-volatile configuration memory.
4096K bytes of packet SRAM memory.

16384K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).
4096K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x2102

 

[IPKONFIG]

I see that they are indeed fast ethernet. The only thing that I can think of is first set your duplex setting to half duplex. Then try and kick the interface speed down to 10Mb. See if that works. If not I'd like to see the interface configuration if you don't mind. Do a "show run inter fa x/x" and post it please.

"I can picture a world without war. A world without hate. A world without fear. And I can picture us attacking that world, because they'd never expect it."
- Jack Handey, Deep Thoughts

 

[NewToo]

IPKONFIG,

Thanks for the help
I found out what is wrong. My Fast Ethernet PA card is 100 mbp only not 10/100.

Thanks
Newtoo