Hi,
one of my switch (backbone) is down, after I reset, all led are yellow and nobody can't connect.
From console I enter reset 1:
Power-on-self-test for Module 1: WS-X2948
Status: (. = Pass, F = Fail)
processor: . cpu sdram: . temperature sensor: .
enet console port: . nvram: . *** ERROR *** ttl=1 addr=70604c08
expected=00000000000c0981 actual=00000000000def81
*** ERROR *** ttl=2 addr=70604c28 expected=00000000000c0985 actual=00000000000de
f85
*** ERROR *** ttl=3 addr=70604c48 expected=00000000000c0989 actual=00000000000de
f89
*** ERROR *** ttl=4 addr=70604c68 expected=00000000000c098d actual=00000000000de
f8d
*** ERROR *** ttl=5 addr=70604c88 expected=00000000000c0991 actual=00000000000de
f91
*** ERROR *** ttl=6 addr=70604ca8 expected=00000000000c0995 actual=00000000000de
f95
switch sram: F
switch registers: . switch port 6: . switch port 7: .
switch bandwidth: .
Module 1 Failed
Power-on-self-test for Module 2: WS-X2948
Port status: (. = Pass, F = Fail, ? = no GBIC)
1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: .
9: . 10: . 11: . 12: . 13: . 14: . 15: . 16: .
17: . 18: . 19: . 20: . 21: . 22: . 23: . 24: .
25: . 26: . 27: . 28: . 29: . 30: . 31: . 32: .
33: . 34: . 35: . 36: . 37: . 38: . 39: . 40: .
41: . 42: . 43: . 44: . 45: . 46: . 47: . 48: .
49: ? 50: ?
Module 2 Passed
Exiting Off-line Diagnostics
Failed Module Bringup Process
Use 'show test 1' to see results of tests
Result from sh test 1:
Module 1 : 0-port Switching Supervisor
POST Results
Network Management Processor (NMP) Status: (. = Pass, F = Fail, U = Unknown)
Galaxy Supervisor Status : F
CPU Components Status
Processor : .
DRAM : .
EEPROM : .
FLASH : .
NVRAM : .
Temperature Sensor : .
Uplink Port 1 : .
Uplink Port 2 : .
SCX1000
Registers : .
Switch Sram : F
Switch Gigaports
0: . 1: . 2: . 3: .
4: . 5: . 6: . 7: .
8: . 9: . 10: . 11: .
Anybody has same problem?
I read from cisco doc, it says hardware failure, I have to replace the module but since the module for 2948g is built in. That means I have to replace the switch???
Can we do hard reset with this switch? if it yes, how?
Any help would be appreciated.
Thanks,
one of my switch (backbone) is down, after I reset, all led are yellow and nobody can't connect.
From console I enter reset 1:
Power-on-self-test for Module 1: WS-X2948
Status: (. = Pass, F = Fail)
processor: . cpu sdram: . temperature sensor: .
enet console port: . nvram: . *** ERROR *** ttl=1 addr=70604c08
expected=00000000000c0981 actual=00000000000def81
*** ERROR *** ttl=2 addr=70604c28 expected=00000000000c0985 actual=00000000000de
f85
*** ERROR *** ttl=3 addr=70604c48 expected=00000000000c0989 actual=00000000000de
f89
*** ERROR *** ttl=4 addr=70604c68 expected=00000000000c098d actual=00000000000de
f8d
*** ERROR *** ttl=5 addr=70604c88 expected=00000000000c0991 actual=00000000000de
f91
*** ERROR *** ttl=6 addr=70604ca8 expected=00000000000c0995 actual=00000000000de
f95
switch sram: F
switch registers: . switch port 6: . switch port 7: .
switch bandwidth: .
Module 1 Failed
Power-on-self-test for Module 2: WS-X2948
Port status: (. = Pass, F = Fail, ? = no GBIC)
1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: .
9: . 10: . 11: . 12: . 13: . 14: . 15: . 16: .
17: . 18: . 19: . 20: . 21: . 22: . 23: . 24: .
25: . 26: . 27: . 28: . 29: . 30: . 31: . 32: .
33: . 34: . 35: . 36: . 37: . 38: . 39: . 40: .
41: . 42: . 43: . 44: . 45: . 46: . 47: . 48: .
49: ? 50: ?
Module 2 Passed
Exiting Off-line Diagnostics
Failed Module Bringup Process
Use 'show test 1' to see results of tests
Result from sh test 1:
Module 1 : 0-port Switching Supervisor
POST Results
Network Management Processor (NMP) Status: (. = Pass, F = Fail, U = Unknown)
Galaxy Supervisor Status : F
CPU Components Status
Processor : .
DRAM : .
EEPROM : .
FLASH : .
NVRAM : .
Temperature Sensor : .
Uplink Port 1 : .
Uplink Port 2 : .
SCX1000
Registers : .
Switch Sram : F
Switch Gigaports
0: . 1: . 2: . 3: .
4: . 5: . 6: . 7: .
8: . 9: . 10: . 11: .
Anybody has same problem?
I read from cisco doc, it says hardware failure, I have to replace the module but since the module for 2948g is built in. That means I have to replace the switch???
Can we do hard reset with this switch? if it yes, how?
Any help would be appreciated.
Thanks,
