Check zone intent error message

[pruden]

Hi all -

I'm trying to add sip trunks to our new cisco call manager (r7)from our cs1000 r 5.5. I have followed some docs that are posted and all seems to go as planned. However, when I try to add the RDB I get an error ---

SCH1613
Only Virtual Trunk zone is allowed.
Check Zone Intent in the LD 117.
Severity: Minor

I can't seem to get around this and I can't find where I need to look in overlay 117. I'm having one of those days.

Does anyone know where to find this information in 117?

Many thanks

 

[bignose21]

LD 117
=> prt inter

You are looking for a zone with an intent of VTRK if you don't have one create one. There are 3 diferent intents MO (Main Office), BMG (Branch Office) and VTRK (Virtual Trunk).

You can get help in 117 by using "?" also you can start a command then use it like:

=> new zone ?

This will give you the help on adding a zone

 

[pruden]

Thanks for the feedback. I guess I had everything right but I'm still a little confused about one thing. We have SIP trunks between two Nortel CS1000 switches and they are using zone 100. I was going to use the same zone for the SIP trunks to the Cisco which is when the error code popped up. I looked at zone 100 in overlay 117 and it is set up as "MO" rather than VTRK. I'm not sure how the guys that were here before got this working with that set up.

I'll set up a new zone and move forward but if anyone has some thoughts on how this works please let me know. Print outs below...


RDB for route 100 - sip tie trunks to another CS1000
TYPE RDB
CUST 00
ROUT 100
DES SIP TRUNKS
TKTP TIE
M911P NO
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK YES <---- Virtual Trunk
ZONE 100 <---- Zone 100
PCID SIP
CRID NO
NODE 1001
DTRK NO
ISDN YES
MODE ISLD
DCH 50
IFC SL1
PNI 00001
NCNA YES
NCRD YES
TRO YES
FALT NO
CTYP UKWN
INAC NO
ISAR NO
DAPC NO
MBXR NO
PTYP ATT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 7100
TCPP NO
TARG
CLEN 10
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
STYP SDAT
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3


PAGE 002

NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6
SST 5 0
NEDC ORG
FEDC ORG
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR YES
INC YES
LAST NO
QREC NO
OAL NO
CDRX NO
VRAT NO
MUS NO
RACD NO
MANO NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO

|Zone|State| Type |Strategy|MO/ | Bandwidth | |BMG/| kbps | |VTRK| ___________________________________________________________
|100| ENL| SHARED| BQ |MO | 1000000| ___________________________________________________________

Thanks

 

[Reusser]

Zone 100 was probably built before you upgraded to 4.5

Before 4.5. there was no zone intent

 

[pruden]

Thanks guys -

Yes - the SIP truks were installed a long time ago so that makes sense. I have a new zone set up and we are going to configure the CM tomorrow so ... fingers crossed ... all should go well. I appreciate the feedback because it just did not make sense. I was looking in all the right places but could not see anything marked VTRK - was going in circles.