Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Wanet Telecoms Ltd on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Caller ID settings on CIDU8 with LG Aria 300

Status
Not open for further replies.
wwwsys

wwwsys

Technical User
Oct 28, 2012
52
AU
I found CLCOB8 and CIDU8 on it and installed. I have 4 analog lines (1 to 4 on CLCOB8) for external. Now I wanna provide Caller ID feature to the internal stations from 100 to 180. Before I call the phone company and ask caller id option I wanna make sure if my settings are ready. Could you help me through the settings please? Please refer the screenshot below.

yd25.png
 
Sort by date Sort by votes
There are two ways to obtain the CID - Caller-ID on analogue lines. One way is DTMF (like Denmark) and the other is FSK (frequency shift keying). From your CO line operator, you need to know what type DTMF or FSK that is delivered.
Hereafter the settings Can be made in the ipLDK.

///doktor
____________________________________
 
Upvote 0 Downvote
I found out that Telstra using FSK so how I should configure it?
 
Upvote 0 Downvote
If you search in the forum for FSK, you Will find the description on howb to do it. I have written the step by step description.
The thread number posted earlier is wrong.

///doktor
____________________________________
 
Upvote 0 Downvote
I found that article after your last message. I initialized and resetted all settings on the CIDU tab. I set the CID Usage to ON and rest of the settings are default (CID Name Display-telephone Number, Serial Port-Not Assigned, CIDU Map Seetings-Not Assigned, CIDU Type Usage-OFF)
I still cannot see the caller id. Is there any settings that I need to check?
Thanks
 
Upvote 0 Downvote
This is according to the manual

Analog Caller ID Service
Description
According to the caller ID standard specification of Bellcore Lab, LDK-300 can support the analog caller ID service. This is the similar to the ISDN CLI service. To use this service, additional external device that is called CIDU(Caller ID Device Unit) is required.

Operation
Similar to ISDN CLI service.

Admin Programming
 CLIP LCD Display (PGM114-BTN1)
 CLI Message Wait (PGM114-BTN4)
 Speed Dial Name Display instead CLI (PGM114-BTN11)
 ISDN CLI Station Number (PGM114-BTN12)
 CIDU Setting (PGM185)
 Incoming Prefix Code Insertion (PGM200-BTN3)
 International Access Code (PGM200-BTN7)
 My Area Code (PGM200-BTN9)
 Area Prefix Code (PGM200-BTN10)

Condition
1. Analog CO line must support the caller ID standard specification of Bellcore Lab.
2. CIDU hardware is required. It must be compatible with LDK-300.
3. Other condition is similar to ISDN CLI service.



///doktor
____________________________________
 
Upvote 0 Downvote
Admin Programming more detailed with my comments:
-------------------------------------------------------------------------------------------
Initialize CID Data THIS HAS TO DONE FIRST - herafter restart the system in PGM450 or with the reset button.
Description
Initialize ADMIN program 185, and recover the default value.
Value : None
-------------------------------------------------------------------------------------------
CID Usage -> ON
Description
If this value is set to ON, CID can be served.
(For UK, System Reset is required after setting CID Usage to ON)
Value : ON=1 / OFF=0
-------------------------------------------------------------------------------------------
CID Name Display -> TELEPHONE Number
Description
Analog CO line CLI carries the caller’s telephone number and name.
According to this ADMIN program value, LCD displayed data can be selected.
If this value is set to NAME, the caller’s name will be displayed on LCD.
If this value is set to TELEPHONE NUMBER, the caller’s telephone number will be displayed on LCD.
Value : NAME=1 / TELEPHONE NO.=0
-------------------------------------------------------------------------------------------
Serial Port Select -> COM1
This is to service CID on analog CO line in IP LDK-300.
Description
This ADMIN program set the port connected to CIDU hardware device.
* Note: This ADMIN program is only needed, when the external CIDU hardware device is installed.
-------------------------------------------------------------------------------------------

CID/CO Line Port Mapping -> Select the lines that should use Callers ID.
Description
When external CID equipment is used, this program set CID port and the analog CO line port
mapping. This is no need when LCOB with optional CID detection board is used
-------------------------------------------------------------------------------------------
CID type • Usage -> set to type 1 - FSK (Type 2 is DTMF)
This is available in IP LDK-300, CID type 1 and 2 is serviced.
Description
If this value is set to ON, CID type 1 service can be used.
-------------------------------------------------------------------------------------------
FAST CID MODE -> Set to ON. (try to set to OFF, if you do not see any CID)
Description
If this value is set to ON, system provides a ring signal to SLT and CID will be displayed after 1st
ringing.
-------------------------------------------------------------------------------------------

Herafter restart the system in PGM450 or with the reset button.
Hope that this can help you.

///doktor
____________________________________
 
Upvote 0 Downvote
More programming:



Admin Programming
 CLIP LCD Display (PGM114-BTN1) _set to ON for all extesnions/stations.

CLIP LCD Display(Calling Line Identification Presentation)
Description
If this value is set to ON, the CLI is displayed on the station’s LCD.
( CO Line Name is not displayed when CLIP is set to ON.)
Value : ON=1 / OFF=0

--------------------------------------------------------------------------------------------

 CLI Message Wait (PGM114-BTN4)

CLI MSG Wait
Description
If this value is set to ON, the station can receive CLI message from CO Incoming call,when the
station doesn’t answer.
Value : ON=1 / OFF=0

--------------------------------------------------------------------------------------------

 Speed Dial Name Display instead CLI (PGM114-BTN11)

CLI Name Display
Description
If this field is ON, the system checks whether the received CLI is matched with the speed dial data or
not. If it is matched, the speed dial name is displayed.
Value : ON=1 / OFF=0
--------------------------------------------------------------------------------------------
 ISDN CLI Station Number (PGM114-BTN12)

ISDN CLI STA
Description
This value is used as outgoing CLI When outgoing CLI is active and CLI type is EXT(Station)
Value : 0~9 (Max 4 digits)
Default value : Logical Station Number.
Leave as is.
--------------------------------------------------------------------------------------------
 CIDU Setting (PGM185)-> see last post
 Incoming Prefix Code Insertion (PGM200-BTN3) -> check your system
 International Access Code (PGM200-BTN7)-> check your system
 My Area Code (PGM200-BTN9)-> check your system
 Area Prefix Code (PGM200-BTN10)-> check your system




///doktor
____________________________________
 
Upvote 0 Downvote
I followed instructions step by step. I also tried Usage Type 2 jyst in case but with some reason I cannot see the Caller IDs :(
 
Upvote 0 Downvote
BTW despite I am using analog lines with CLCOB8+CIDU8, is still relevant to use ISDN settings?
 
Upvote 0 Downvote
If you can listen to "what happpens before the Phone rings" with a line amplifier , connected to the phone line, then you could hear the FSK tones.
I guess that these FSK tones are not sent to you.

If possible keep the ISDN settings since CID in the ipLDK/Aria is based on this signaling.

///doktor
____________________________________
 
Upvote 0 Downvote
It may also be worthwhile to connect a caller ID capable analogue phone to the line to ensure it is actually being sent.

I have had no problems with CID on analogue. We do only have two line providers here though. SIP not included naturally.

 
Upvote 0 Downvote
Hi,

I did like you said and analogue phone showed the caller id sucessfully. That means we have something to do with the pbx system.
 
Upvote 0 Downvote
According to screenshot below, is there anything to correct?
n6xk.png
 
Upvote 0 Downvote
Have you mapped the CIDU ports to the trunks?

PGM 185

Button 1 = on

Button 2 = telephone no

Button 3 = N/A

Button 4 = set 0-1 , 1-2 , 2-3, 3-4. ( This assigns CLID ports to trunk ports so could be 1-1,2-2,3-3,4-4 if you like )
 
Upvote 0 Downvote
Hi,

After your message I mapped the CIDU ports as you have described. Still no caller ID :( All I can see is "Hunt Ringing" since the beginning. Is there any other place to check the settings?
 
Upvote 0 Downvote
Unfortunately I believe if your calls go to a hunt group, the CLI will not display until the call is answered.

Reprogram the CO lines to ring an individual extn and see if the CLI is presented.
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

tecdigi
  • Locked
  • Question
PSU LG LDK-100 SCHEMATIC HELP..
Replies
0
Views
581
tecdigi
tecdigi
JWNS
  • Locked
  • Question
LG LDK 100 Help!
Replies
4
Views
726
Antoniojhone
Antoniojhone
seif1979
  • Locked
  • Question
LDP 9208D with LG LDK IP 60
Replies
0
Views
221
seif1979
seif1979
G
  • Locked
  • Question
Refurb LDP-9030D UK base unit won't boot on IPECs
Replies
2
Views
279
gamesgenie
G
majulal
  • Locked
  • Question
lg ericsson ipecs emg800 web access not connecting but ping is working please help
Replies
1
Views
583
rsatech
rsatech

Part and Inventory Search

Sponsor

Back
Top