I'm setting up Call Manager 3.3 to access a 3640 gateway running in H.323 mode - Our call manager server is just one of many devices connected to the gateway. Are there any special considerations/configurations to take into account? Everything looks pretty straight forward, but I'm having problems dialing out.
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Call Manager 3.3 on a Shared Gateway
- Thread starter Aluffy
- Start date
- Thread starter
- #4
The test configuration is as follows:
!
dial-peer voice 9440 voip
destination-pattern 13015849430
progress_ind setup enable 3
voice-class h323 9430
session target ipv4:69.139.229.31
dtmf-relay h245-signal h245-alphanumeric
codec g711ulaw
!
dial-peer voice 9441 pots
destination-pattern 1T
no digit-strip
direct-inward-dial
port 2/0:23
--- I think for the most part, the call manager portion is an easy setup (and I believed I got that figured out) - However, the gateway tech is telling me that when the number is dialed from a PSTN into the gateway, the gateway never sends a packet to the session target - it just searches and rolls over the port?
!
dial-peer voice 9440 voip
destination-pattern 13015849430
progress_ind setup enable 3
voice-class h323 9430
session target ipv4:69.139.229.31
dtmf-relay h245-signal h245-alphanumeric
codec g711ulaw
!
dial-peer voice 9441 pots
destination-pattern 1T
no digit-strip
direct-inward-dial
port 2/0:23
--- I think for the most part, the call manager portion is an easy setup (and I believed I got that figured out) - However, the gateway tech is telling me that when the number is dialed from a PSTN into the gateway, the gateway never sends a packet to the session target - it just searches and rolls over the port?
computerhighguy
IS-IT--Management
Since this is a PRI, I would imagine that you are using DNIS. Change to this.
dial-peer voice 9441 pots
destination-pattern .
It will accept all calls from the PRI as an inbound call. You will then need to add a dial peer for your call manager system depending on how you are getting your digits.
Keep in mind that a call coming into a gateway needs 2 dial peers.
An inbound dial peer and an outbound dial peer
If you are using DNIS digits 5510-5529 then here is an example of a dial peer you will need to send the call to callmanager.
dial-peer voice 5 voip
description Inbound DNIS
destination-pattern 55[1,2].
session target ipv4:10.5.1.4
ip qos dscp cs6 media
no vad
It is what it is!!
__________________________________
A+, Net+, I-Net+, Certified Web Master, MCP, MCSA, MCSE, CCNA, CCDA, and few others (I got bored one day)
dial-peer voice 9441 pots
destination-pattern .
It will accept all calls from the PRI as an inbound call. You will then need to add a dial peer for your call manager system depending on how you are getting your digits.
Keep in mind that a call coming into a gateway needs 2 dial peers.
An inbound dial peer and an outbound dial peer
If you are using DNIS digits 5510-5529 then here is an example of a dial peer you will need to send the call to callmanager.
dial-peer voice 5 voip
description Inbound DNIS
destination-pattern 55[1,2].
session target ipv4:10.5.1.4
ip qos dscp cs6 media
no vad
It is what it is!!
__________________________________
A+, Net+, I-Net+, Certified Web Master, MCP, MCSA, MCSE, CCNA, CCDA, and few others (I got bored one day)
- Status
Similar threads
- Locked
- Question
- Question