I have a TN2198 BRI board and i am attempting to replace the CO provided BRI's. These are currently running to an NT1 device then to the MCU or Conference MUX a Tandberg 6000. I have the trunks up and IDLE. I can dial out and connect to the distant end test site...however i can only get a max of 5 channels to "bond".....Even if I choose the options for 5-12 channels bonded on the mux...Here are my configs and I would appreciate anyones input. BTW the PRI's I route them too are provided by Qwest and are dedicated LD.
nge bri-trunk-board 02a06 Page 1 of 2 SPE B
ISDN-BRI TRUNK CIRCUIT PACK
Location: 02A06 Name: Test
Interface Companding: a-law DCP/Analog Bearer Capability: 3.1kHz
Port Interface Side Cntry/Peer TEI Time Invert
Protocol Fill Bits?
1: network 10 auto ones n
2: network 10 auto ones n
3: network 10 auto ones n
4: network 10 auto ones n
5: network 10 auto ones n
6: network 10 auto ones n
7: 0 ones n
8: 0 ones n
9: 0 ones n
10: 0 ones n
11: 0 ones n
12: 0 ones n
Port Interwork XID Endpt SPID Endpt Max
Message Test? Init? ID NCA TSC
1: PROGress n n 0
2: PROGress n n 0
3: PROGress n n 0
4: PROGress n n 0
5: PROGress n n 0
6: PROGress n n 0
7: PROGress n n 0
8: PROGress n n 0
9: PROGress n n 0
10: PROGress n n 0
11: PROGress n n 0
12: PROGress n n 0
change trunk-group 6 Page 1 of 19 SPE B
TRUNK GROUP
Group Number: 6 Group Type: isdn CDR Reports: y
Group Name: BRI COR: 18 TN: 1 TAC: 276
Direction: two-way Outgoing Display? n Carrier Medium: PRI/BRI
Dial Access? y Busy Threshold: 255 Night Service:
Queue Length: 0
Service Type: tie Auth Code? n TestCall ITC: unre
Far End Test Line No:
TestCall BCC: 4
TRUNK PARAMETERS
Codeset to Send Display: 6 Codeset to Send National IEs: 6
Max Message Size to Send: 260 Charge Advice: none
Supplementary Service Protocol: a Digit Handling (in/out): overlap/overlap
Digit Treatment: Digits:
Trunk Hunt: cyclical QSIG Value-Added? n
Digital Loss Group: 13
Calling Number - Delete: Insert: Numbering Format:
Bit Rate: 1200 Synchronization: async Duplex: full
Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 0
ge trunk-group 6 Page 2 of 19 SPE B
TRUNK FEATURES
ACA Assignment? n Measured: none Wideband Support? n
Internal Alert? n Maintenance Tests? y
Data Restriction? n NCA-TSC Trunk Member:
Send Name: n Send Calling Number: y
Used for DCS? n
Suppress # Outpulsing? n Numbering Format: public
Outgoing Channel ID Encoding: preferred UUI IE Treatment: service-provider
Replace Restricted Numbers? n
Replace Unavailable Numbers? n
Send Connected Number: y
Send UUI IE? y
Send UCID? n
Send Codeset 6/7 LAI IE? y Ds1 Echo Cancellation? n
US NI Delayed Calling Name Update? n
SBS? n Network (Japan) Needs Connect Before Disconnect? n
ROUP MEMBER ASSIGNMENTS Total Administered Members: 12
Port Code Sfx Name Night Sig Grp
1: 02A0601 TN2198
2: 02A0617 TN2198
3: 02A0602 TN2198
4: 02A0618 TN2198
5: 02A0603 TN2198
6: 02A0619 TN2198
7: 02A0604 TN2198
8: 02A0620 TN2198
9: 02A0605 TN2198
10: 02A0621 TN2198
11: 02A0606 TN2198
12: 02A0622 TN2198
13:
14:
15:
BCC's are fine as are the cor frl etc as I said i can dial out and connect...and hold the connect. The PBX is a G3R 1.3 with all the bells and whistles related to isdn that are required.
Any help greatly appreciated.
nge bri-trunk-board 02a06 Page 1 of 2 SPE B
ISDN-BRI TRUNK CIRCUIT PACK
Location: 02A06 Name: Test
Interface Companding: a-law DCP/Analog Bearer Capability: 3.1kHz
Port Interface Side Cntry/Peer TEI Time Invert
Protocol Fill Bits?
1: network 10 auto ones n
2: network 10 auto ones n
3: network 10 auto ones n
4: network 10 auto ones n
5: network 10 auto ones n
6: network 10 auto ones n
7: 0 ones n
8: 0 ones n
9: 0 ones n
10: 0 ones n
11: 0 ones n
12: 0 ones n
Port Interwork XID Endpt SPID Endpt Max
Message Test? Init? ID NCA TSC
1: PROGress n n 0
2: PROGress n n 0
3: PROGress n n 0
4: PROGress n n 0
5: PROGress n n 0
6: PROGress n n 0
7: PROGress n n 0
8: PROGress n n 0
9: PROGress n n 0
10: PROGress n n 0
11: PROGress n n 0
12: PROGress n n 0
change trunk-group 6 Page 1 of 19 SPE B
TRUNK GROUP
Group Number: 6 Group Type: isdn CDR Reports: y
Group Name: BRI COR: 18 TN: 1 TAC: 276
Direction: two-way Outgoing Display? n Carrier Medium: PRI/BRI
Dial Access? y Busy Threshold: 255 Night Service:
Queue Length: 0
Service Type: tie Auth Code? n TestCall ITC: unre
Far End Test Line No:
TestCall BCC: 4
TRUNK PARAMETERS
Codeset to Send Display: 6 Codeset to Send National IEs: 6
Max Message Size to Send: 260 Charge Advice: none
Supplementary Service Protocol: a Digit Handling (in/out): overlap/overlap
Digit Treatment: Digits:
Trunk Hunt: cyclical QSIG Value-Added? n
Digital Loss Group: 13
Calling Number - Delete: Insert: Numbering Format:
Bit Rate: 1200 Synchronization: async Duplex: full
Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 0
ge trunk-group 6 Page 2 of 19 SPE B
TRUNK FEATURES
ACA Assignment? n Measured: none Wideband Support? n
Internal Alert? n Maintenance Tests? y
Data Restriction? n NCA-TSC Trunk Member:
Send Name: n Send Calling Number: y
Used for DCS? n
Suppress # Outpulsing? n Numbering Format: public
Outgoing Channel ID Encoding: preferred UUI IE Treatment: service-provider
Replace Restricted Numbers? n
Replace Unavailable Numbers? n
Send Connected Number: y
Send UUI IE? y
Send UCID? n
Send Codeset 6/7 LAI IE? y Ds1 Echo Cancellation? n
US NI Delayed Calling Name Update? n
SBS? n Network (Japan) Needs Connect Before Disconnect? n
ROUP MEMBER ASSIGNMENTS Total Administered Members: 12
Port Code Sfx Name Night Sig Grp
1: 02A0601 TN2198
2: 02A0617 TN2198
3: 02A0602 TN2198
4: 02A0618 TN2198
5: 02A0603 TN2198
6: 02A0619 TN2198
7: 02A0604 TN2198
8: 02A0620 TN2198
9: 02A0605 TN2198
10: 02A0621 TN2198
11: 02A0606 TN2198
12: 02A0622 TN2198
13:
14:
15:
BCC's are fine as are the cor frl etc as I said i can dial out and connect...and hold the connect. The PBX is a G3R 1.3 with all the bells and whistles related to isdn that are required.
Any help greatly appreciated.
please....