Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

BRI incorrect spids

Status
Not open for further replies.
rkmorrow

rkmorrow

MIS
Joined
Jan 12, 2001
Messages
98
Location
US
I have a connection I am trying to get up, it has never been in service and the router (cisco 2610xm)has a new config.
Verizon has verified the spids and connection several times as being good. I cannot get the connection to the switch to show everything is ok. At one point one of the bri lines said the spid was ok, but now both are down. I have the config, sh isdn stat, and short sample of debug q921 attached, any help would be appreciated.

Whaven_RTR_CCNB#
Whaven_RTR_CCNB#debug isdn q921
debug isdn q921 is ON.
Whaven_RTR_CCNB#term mon
Whaven_RTR_CCNB#
00:10:22: ISDN BR1/1 Q921: User TX -> INFO sapi=0 tei=67, ns=5 nr=5
00:10:22: ISDN BR1/1 Q921: User RX <- RR sapi=0 tei=67 nr=6
00:10:22: ISDN BR1/1 Q921: User RX <- INFO sapi=0 tei=67, ns=5 nr=6
00:10:22: ISDN BR1/1 Q921: User TX -> RR sapi=0 tei=67 nr=6
00:10:94489280576: ISDN Error: Invalid DSL (13) **ERROR**: CCBNI1_CallOriginat
e: Setup was rejected, cause = 50
00:10:98784247807: ISDN BR1/1 **ERROR**: host_disconnect_ack: Unfound B-channel
on Disconnect_Ack call id 0x800A
00:10:223338299392: ISDN BR1/1 **ERROR**: CCBRI_Go: NO CCB Src->HOST call id 0x8
00A, event 0x5 ces 1
00:10:52: ISDN BR1/1 Q921: User TX -> RRp sapi=0 tei=67 nr=6
00:10:52: ISDN BR1/1 Q921: User RX <- RRf sapi=0 tei=67 nr=6
00:11:20: ISDN BR1/1 Q921: User TX -> INFO sapi=0 tei=67, ns=6 nr=6
00:11:20: ISDN BR1/1 Q921: User RX <- RR sapi=0 tei=67 nr=7
00:11:20: ISDN BR1/1 Q921: User RX <- INFO sapi=0 tei=67, ns=6 nr=7
00:11:20: ISDN BR1/1 Q921: User TX -> RR sapi=0 tei=67 nr=7
00:11:85899345984: ISDN Error: Invalid DSL (13) **ERROR**: CCBNI1_CallOriginat
e: Setup was rejected, cause = 50
00:11:90194313215: ISDN BR1/1 **ERROR**: host_disconnect_ack: Unfound B-channel
on Disconnect_Ack call id 0x800B
00:11:43: ISDN BR1/1 Q921: User RX <- IDCKRQ ri=0 ai=127
00:11:43: ISDN BR1/1 Q921: User TX -> IDCKRP ri=48386 ai=67
00:11:44: ISDN BR1/1 Q921: User RX <- IDCKRQ ri=0 ai=127
00:11:44: ISDN BR1/1 Q921: User TX -> IDCKRP ri=36131 ai=67
00:11:214748364800: ISDN BR1/1 **ERROR**: CCBRI_Go: NO CCB Src->HOST call id 0x8
00B, event 0x5 ces 1
00:11:50: ISDN BR1/1 Q921: User TX -> RRp sapi=0 tei=67 nr=7
00:11:50: ISDN BR1/1 Q921: User RX <- RRf sapi=0 tei=67 nr=7
00:12:15: ISDN BR1/1 Q921: User TX -> INFO sapi=0 tei=67, ns=7 nr=7
00:12:15: ISDN BR1/1 Q921: User RX <- RR sapi=0 tei=67 nr=8
00:12:15: ISDN BR1/1 Q921: User RX <- INFO sapi=0 tei=67, ns=7 nr=8
00:12:15: ISDN BR1/1 Q921: User TX -> RR sapi=0 tei=67 nr=8
00:12:64424509504: ISDN Error: Invalid DSL (13) **ERROR**: CCBNI1_CallOriginat
e: Setup was rejected, cause = 50
00:12:68719476735: ISDN BR1/1 **ERROR**: host_disconnect_ack: Unfound B-channel
on Disconnect_Ack call id 0x800C
Whaven_RTR_CCNB#
00:12:193273528320: ISDN BR1/1 **ERROR**: CCBRI_Go: NO CCB Src->HOST call id 0x8
00C, event 0x5 ces 1
00:12:45: ISDN BR1/1 Q921: User TX -> RRp sapi=0 tei=67 nr=8
00:12:45: ISDN BR1/1 Q921: User RX <- RRf sapi=0 tei=67 nr=8
Whaven_RTR_CCNB#u all
All possible debugging has been turned off
Whaven_RTR_CCNB#debug isdn q931
debug isdn q931 is ON.
Whaven_RTR_CCNB#
00:13:06: ISDN BR1/1 Q931: TX -> SETUP pd = 8 callref = 0x0D
Bearer Capability i = 0x8890
Standard = CCITT
Transer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0x83
Keypad Facility i = '7042621424'
00:13:06: ISDN BR1/1 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x8D
Cause i = 0x82B2 - Requested facility not subscribed
00:13:25769803840: ISDN Error: Invalid DSL (13) **ERROR**: CCBNI1_CallOriginat
e: Setup was rejected, cause = 50
00:13:30064771071: ISDN BR1/1 **ERROR**: host_disconnect_ack: Unfound B-channel
on Disconnect_Ack call id 0x800D
00:13:154618822656: ISDN BR1/1 **ERROR**: CCBRI_Go: NO CCB Src->HOST call id 0x8
00D, event 0x5 ces 1
00:14:01: ISDN BR1/1 Q931: TX -> SETUP pd = 8 callref = 0x0E
Bearer Capability i = 0x8890
Standard = CCITT
Transer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0x83
Keypad Facility i = '7042621424'
00:14:01: ISDN BR1/1 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x8E
Cause i = 0x82B2 - Requested facility not subscribed
00:14:4294967360: ISDN Error: Invalid DSL (13) **ERROR**: CCBNI1_CallOriginate
: Setup was rejected, cause = 50
00:14:8589934591: ISDN BR1/1 **ERROR**: host_disconnect_ack: Unfound B-channel o
n Disconnect_Ack call id 0x800E
00:14:133143986176: ISDN BR1/1 **ERROR**: CCBRI_Go: NO CCB Src->HOST call id 0x8
00E, event 0x5 ces 1
Whaven_RTR_CCNB#u all
All possible debugging has been turned off
Whaven_RTR_CCNB#





User Access Verification

Password:
Whaven_RTR_CCNB>en
Password:
Whaven_RTR_CCNB#sh isdn stat
Global ISDN Switchtype = basic-ni
ISDN BRI1/0 interface
dsl 8, interface ISDN Switchtype = basic-ni
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 8 CCBs = 0
The Free Channel Mask: 0x00000000
ISDN BRI1/1 interface
dsl 9, interface ISDN Switchtype = basic-ni
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 67, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
TEI 67, ces = 1, state = 6(not initialized)
spid1 configured, no LDN, spid1 sent, spid1 NOT valid
TEI Not Assigned, ces = 2, state = 1(terminal down)
spid2 configured, no LDN, spid2 NOT sent, spid2 NOT valid
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 9 CCBs = 0
The Free Channel Mask: 0x80000003
ISDN BRI1/2 interface
dsl 10, interface ISDN Switchtype = basic-ni
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 10 CCBs = 0
The Free Channel Mask: 0x00000000

Whaven_RTR_CCNB#sh conf
Using 2019 out of 29688 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname &quot;Whaven_RTR_CCNB&quot;
!
enable secret 5 $1$pTvE$baQYNbe4ltLWYnnLx/xjl1
enable password 7 09435D00
!
username TFA_Fast_Recovery password 7 060B0A334047075A54
ip subnet-zero
!
!
!
ipx routing 000a.f44c.5760
isdn switch-type basic-ni
!
!
!
!
interface FastEthernet0/0
description Connection to Winter Haven
ip address 10.50.4.1 255.255.0.0
ip helper-address 10.11.1.1
no ip redirects
no ip route-cache
no ip mroute-cache
duplex auto
speed auto
ipx network 50 encapsulation SAP
ipx type-20-propagation
!
interface Serial0/0
no ip address
no ip redirects
no ip route-cache
no ip mroute-cache
!
interface Serial0/1
description connection to Bartow2_RTR
bandwidth 576
ip address 10.51.4.2 255.255.0.0
no ip redirects
encapsulation ppp
no ip route-cache
no ip mroute-cache
ipx network 51
!
interface bri1/0
no ip address
shutdown
isdn switch-type basic-ni
!
interface BRI1/1
no ip address
encapsulation ppp
no ip route-cache
no ip mroute-cache
dialer pool-member 1
isdn switch-type basic-ni
isdn spid1 86329390750101
isdn spid2 86329390630101
ppp authentication chap
ppp multilink
!
interface BRI1/2
no ip address
shutdown
isdn switch-type basic-ni
!
interface BRI1/3
no ip address
shutdown
isdn switch-type basic-ni
!
interface Dialer0
ip address 10.10.13.6 255.255.255.252
encapsulation ppp
dialer pool 1
dialer remote-name TFA_Fast_Recovery
dialer string 7042621424
dialer-group 5
ppp authentication chap callin
ppp multilink
!
router rip
network 10.0.0.0
!
ip classless
ip route 0.0.0.0 0.0.0.0 10.11.1.8
ip route 10.11.0.0 255.255.0.0 Dialer0 150
ip http server
ip pim bidir-enable
!
!
dialer-list 5 protocol ip permit
!
!
!
!
line con 0
line aux 0
line vty 0 4
password 7 00170B0709484853
login
!
!
end

Whaven_RTR_CCNB#
 
Sort by date Sort by votes
Dear Friend,
Have yiu got any solution on the problem. I am also facing the same problem with cisco 1721 router but iam not using any SPIDs.
If the problem is solved can you please brief me also.

Thanks

Sandeep Sutar.
 
Upvote 0 Downvote
We have had simular problems with a number of carriers nationwide. Try verifying that the SPIDs has been assigned in the carrier switches as 64K Data only on BOTH channels. Sometimes the ISDN circuits are implemented with a default setting that supports voice and data. Also verify the Carrier's switch type. You are set for National but it looks like the carrier switch may be set for 5ess. You have comms with the carrier equipment so it is definitely not a connectivity issue. Also you might try attempting a few tests calls without the CHAP and PPP Multilink settings. One thing we have found is that PPP multilink has given us a few &quot;issues&quot; when configured on the BRI interface. You can try connecting without using Multilink at all and see what happens. Did you run &quot;debug ppp multi&quot;? Might try &quot;debug ISDN code&quot; as well. Good luck.
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

unixbof
  • Locked
  • Question Question
BRI PCI card on a PRI line
Replies
1
Views
260
libram11
libram11
RadarGuy1962
  • Locked
  • Question Question
Gigabit Ethernet wiring incorrect
Replies
11
Views
588
daronwilson
daronwilson
fhouston
  • Locked
  • Question Question
bri to pri
Replies
3
Views
158
ISDNman
ISDNman
train2006
  • Locked
  • Question Question
BRI trunk admin for g350 gateway
Replies
3
Views
149
ISDNman
ISDNman
adamandamy
  • Locked
  • Question Question
conference bridge
Replies
2
Views
176
pbx2sip
pbx2sip

Part and Inventory Search

Sponsor

Back
Top