bought the mitel 3300 cxi controller pbx. Need Help

[apasha123]

When I start this controller following results start.

MITEL SYSTEM ROM R3.0/6 May 26 2009 (80 - POWER_ON_RESET)

CCA Number : 56009216 RD.1
System Model : 00610001 F100
CPU Model : 8360 R8048000021
Reset Config Low : 08030008
Reset Config High : b4500006
Coherent System Bus Clock (MHz) : 266
CPM Clock (MHz) : 266
Core Clock (MHz) : 399
DDR Clock (MHz) : 133
Local Bus Clock (MHz) : 66
Input Clock (MHz) : 33
Internal Memory Map : f0000000
Main Memory (MB) : 512
Local Memory (MB) : 0
Flash Memory (MB) : 2
MAC Address : 08000f855c56
L2 Switch : 1
POST Bypass : 0
Watchdog Bypass : 0
Slot Id : 0

Starting POST...

SDRAM CS1 Data Bit Walk 1................... PASSED
SDRAM CS1 Data Bit Walk 0................... PASSED
SDRAM CS2 Data Bit Walk 1................... PASSED
SDRAM CS2 Data Bit Walk 0................... PASSED
SDRAM CS1 Address Walk 1................... PASSED
SDRAM CS1 Address Walk 0................... PASSED
SDRAM CS2 Address Walk 1................... PASSED
SDRAM CS2 Address Walk 0................... PASSED
SDRAM CS1 March Test........................ PASSED
SDRAM CS2 March Test........................ PASSED

Starting vxWorks...

VxWorks System Boot


Copyright 1984-2002 Wind River Systems, Inc.


CPU: Mitel Embedded PPC83XX F100
Version: VxWorks5.5.2
BSP version: 3.0/6
Creation date: May 26 2009, 11:27:13

Press <SPACE><SPACE><SPACE> to stop auto-boot AFTER countdown starts...
<7><6><5> <4><3> <2><1>
[VxWorks Boot]: version


VxWorks System Boot

Copyright 1984-2002 Wind River Systems, Inc.
CPU: Mitel Embedded PPC83XX F100
Version: VxWorks5.5.2
BSP version: 3.0/6
Creation date: May 26 2009, 11:27:13

[VxWorks Boot]:




there is no ip address. how I can access the device through GUI???

 

[wireman50]

Assuming it goes no further than that then its not booting. When you get to the 'Press <space> <space> ' bit you can stop the auto boot and change settings for IP address but I wonder if it either has no HD or its been wiped....?

 

[jpruder]

maybe pressing space space space and then c at the prompt and enter may give some additional info

 

[apasha123]

thanks for reply.

I did but there is nothing please see the result

[VxWorks Boot]: c

'.' = clear field; '-' = go to previous field; ^D = quit

boot device : 0
processor number : 0
host name :
file name :
inet on ethernet (e) :
inet on backplane (b):
host inet (h) :
gateway inet (g) :
user (u) :
ftp password (pw) (blank = use rsh):
flags (f) : 0x0
target name (tn) :
startup script (s) :
other (o) :

Please guide me how I access this device through GUI.

 

[wireman50]

You can't get to the gUI until you have it fully booted. First check to see if there is a hard disk installed. I suspect not. If there is you will have to load software. If you do you will need access to MOL to get hold of a software release amd maybe you will be lucky and the orignal vendor may not have scrubbed it from their AMC account. If they have then your stuffed, you will have to purchase licences from a vendor.

 

[nytalkin]

The bootline is blank. I suspect the system has been wiped clean. Without an Application record and licensing you have purchased a doorstop.

NO GOOD DEED GOES UNPUNISHED!