Can we ignored an attendant feature and focus to configuration how to get outgoing line with access code "0"? Because my latest configuration below is not successfull to get outgoing line when i dialed "0". When i dialed "0" there is error message on OpenStage 15T diplay "Currently not accessible". May i missed some parameter? any advice for this case is important for me.
LTG 1 LTU 1 SRCGRP 1 ALARMNO-LTU 0
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
| | | |S|H|AL-| | | |
| ASSIGNED | MODULE |FCT|E|W|ARM| | INSERTED | HW- | MODULE
PEN | MODULE | TYPE |ID |C|Y|NO | | MODULE |STATE INFO | STATUS
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
1 | Q2324-X500 STMI4 1 A 0|*| | | NPR
+--------------------------------+-+------------+------------+------------
| IP ADDRESS : 192.168. 0. 30 B-CHANNELS : 60 BCHLCNT : 60
| IP MODE : IPV4 DHCP V4 : NO DHCP V6 : NO
| BLOCK NO : 1 PRERESERVED LINES ASSIGNED : NO
| 1. FUNCT : HG3550 1 LINES B-CHANNELS : 20 BCHLCNT : 20
| 2. FUNCT : HG3530 50 LINES B-CHANNELS : 20 BCHLCNT : 20
| 3. FUNCT : SIP 100 LINES B-CHANNELS : 20 BCHLCNT : 20
+--------------------------------+-+------------+------------+------------
2 | Q2168-X SLMO24 1 A 0| | Q2168-X | 1 -11 - | READY
3 | Q2227-X SLMAV A 0| | Q2227-X | 1 -14 - | READY
4 | Q2227-X SLMAV A 0| | Q2227-X | 1 -14 - | READY
5 | Q2227-X SLMAV A 0| | Q2227-X | 1 -14 - | READY
6 | Q2327-X100 TMANI A 0| | Q2327-X100 | 1 -11 - | READY
7 | Q2266-X LTUCA 0| | Q2266-X | 1 -15 - | READY
8 | Q2327-X100 TMANI A 0| | Q2327-X100 | 1 -11 - | READY
9 | Q2227-X SLMAV A 0| | Q2227-X | 1 -14 - | READY
10 | Q2227-X SLMAV A 0| | Q2227-X | 1 -14 - | READY
11 | Q2227-X SLMAV A 0| | Q2227-X | 1 -14 - | READY
12 | Q2227-X SLMAV A 0| | Q2227-X | 1 -14 - | READY
13 | Q2227-X SLMAV A 0| | Q2227-X | 1 -14 - | READY
14 | Q2227-X SLMAV A 0| | Q2227-X | 1 -14 - | READY
+----+----+---------------------------+-+------------+------------+--------+
| NO SECURITY STATUS AVAILABLE, SINCE FEATURE SPE IS NOT ACTIVATED |
+---------+----------------------------------------------------------------+
AMO-BCSU -111 BOARD CONFIGURATION, SWITCHING UNIT
DISPLAY COMPLETED;
*)Its my latest configuration today
ADD-WABE:0,,,CO,N,,,,,,,,;
ADD-WABE:9,,,ATNDIND,N,,,,,,,,;
ADD-COP:40,DTMF&SFRM&RLSA&BR64&TDED&NO1A&DITW&TIM1&NSDL&IDP2&DTM1,,;
CHANGE-COP:40,COPADD,,,,INDEP,"TMANI-DTMF";
ADD-COT: 40,XFER&CHRT&NTON;
CHANGE-COT:40,COTADD,,INDEP,"TMANI-DTMF";
ADD-COSSU:,8,,,,,,,,"";
CHA-COSSU:COS,8,TA&TSUID&TNOTCR&COSXCD&MB&VCE&FWDNWK&TTT;
CHA-COSSU:COS,8,FWDECA&FWDEXT;
CHA-COSSU:COS,8,,NOCO&NOTIE;
CHA-COSSU:COS,8,,,NOCO&NOTIE;
CHA-COSSU:LCOSV,5,1&&5;
CHA-COSSU:LCOSV,5,,,,,0;
ADD-LODR:ODR=1,CMD=ECHO,FIELD=2;
ADD-LODR:ODR=1,CMD=END;
ADD-LODR:ODR=1,INFO="TMANI";
*)Change PTIME:REST,PARA to get clear voice - Indonesia only. (not noise as before it change)
COPY-PTIME:119,0;
CHANGE-PTIME:REST,0,PARA,,,,,12,65,,,,,6,,,16;
ADD-BUEND:100,"SARWONO",8 ,0 ,* ,1 ,ON ,0 ,0 ,NEUTRAL;
ADD-TACSU:1-1-8-0,,40,40,0,0,8,5,1,,100,0,"SARWONO",0,,2,1,EMPTY,0,NONE,NONE,0,EC&G711&G729AOPT,"",0,GDTR,0,,Y,TC,TMANIMSG,0,3208,0,0,1,0,1,0,DTMF-DTMF,0-0,0,;
ADD-RICHT:LRTENEW,40,VCE,"TMANI",100,1,,NO,,,"",,,,,,NO,NO,"",0,NEUTRAL,NO,NO,NO,NO,NO,NO,NO,NO ;
ADD-LDAT:40,VCE,1,,100,1,1,,1,EMPTY,NONE,,4,,,,,,,,,,,,;
ADD-LDPLN:LCRPATT,0,0-XXX,0&1&2&3&4&5&6&7&8&9&10&11&12&13&14&15,40,,,1,,,,N;
*)I used this station configuration to make outgoing call
ADD-SBCSU:3208,OPTI,DIR,1-1-2-22,OPTIP500,1,5,1,5,1,1,1,0,0,N,0,0,,,N,0,0,N,,,Y,0,N,N,N,Y,N,,,,,,,,5,,,,N,NORMAL,Y,ENGLISH,0,,,0,,,,,,,,,,,;
ADD-SCSU:1200,1-1-3-0,ANATE,0,0,5,1,5,1,1,1,,,0,0,0,1,,DTMF,,,,ENGLISH,YES,,NO,,,,0,DIR,YES,NO,0,;
