Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

911 & 9911 not working, giving outside DT

Status
Not open for further replies.
bigchiefdan

bigchiefdan

IS-IT--Management
Joined
Apr 9, 2007
Messages
116
Location
US
ok, i test these every time a change is made to telco and/or annually.

Im running Cisco Unified Call Manager System version: 6.1.3.1000-16. I have 8 locations, this is happening to all 8.

The last time I tested it (early this year, no changes just a test) it worked. I could pick up the phone and press 911, call would go to the 911 center. I could also press 9911 and it would yield the same results.

Now when you dial 911 nothing happens. when I dial 9911, I am presented with dialtone again, but it does not sound like the normal DT that call manger uses. its almost like im being connected directly to the phone line.

Im using POTS at all the gateways. I have the route patterns setup the same as from installation (no changes or mods). The gateways have not been changed.

The only way to reach 911 is to: pick up phone, dial 9911, wait for abnormal dial tone, then dial 911 again.
At that point it routes ok as the address is being verified and matches the site it should.
Any ideas?
 
Sort by date Sort by votes
I would start by running DNA and see what path the 911 calls are taking and what is being passed to the PSTN.
 
Upvote 0 Downvote
where do I find that? I do not see it listed in the plugins.
 
Upvote 0 Downvote
disregard, I found the location. I will review and check back.
thanks,
 
Upvote 0 Downvote
Ok. After running the analyzer with multiple scenarios, all the results appear the same. These results also match the results I get when I use a number that is routed correctly. is there anything at the Gateway level that I should look at even though nothing has changed? I am planning on rebooting the system tonight after hours.
 
Upvote 0 Downvote
are your gateways h323 or mgcp? if h323 it could be an issue with your dial-peers.
i doubt a reboot will fix it but worth a try.
can you post the dna output and your dial-peers if you are doing h323?
 
Upvote 0 Downvote
held off on the reboot.
All GWs are h323.
*start C&P*
dial-peer voice 9101 pots
preference 2
destination-pattern 9T
progress_ind setup enable 3
progress_ind progress enable 8
port 0/0/0
!
dial-peer voice 9110 pots
preference 1
destination-pattern 9T
port 0/0/1
!
dial-peer voice 9111 pots
preference 3
destination-pattern 9T
progress_ind setup enable 3
progress_ind progress enable 8
port 0/0/2
!
dial-peer voice 9100 pots
preference 4
destination-pattern 9T
progress_ind setup enable 3
progress_ind progress enable 8
port 0/0/3
!
dial-peer voice 9211 pots
preference 5
destination-pattern 9T
progress_ind setup enable 3
progress_ind progress enable 8
port 0/1/0
!
dial-peer voice 9200 pots
preference 6
destination-pattern 9T
progress_ind setup enable 3
progress_ind progress enable 8
port 0/1/1
!
dial-peer voice 2000 voip
preference 1
destination-pattern 59..
modem passthrough nse codec g711ulaw
session target ipv4:10.0.3.10
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
!
dial-peer voice 2001 voip
preference 1
destination-pattern 3...
modem passthrough nse codec g711ulaw
session target ipv4:10.0.3.10
dtmf-relay h245-alphanumeric
codec g711ulaw
fax-relay ecm disable
no vad
!
dial-peer voice 9302 pots
preference 5
destination-pattern 9T
progress_ind setup enable 3
progress_ind progress enable 8
port 0/2/2
!
dial-peer voice 9304 pots
preference 6
destination-pattern 9T
progress_ind setup enable 3
progress_ind progress enable 8
port 0/2/3
!
dial-peer voice 9301 pots
preference 10
destination-pattern 9T
progress_ind setup enable 3
progress_ind progress enable 8
port 0/2/1
!
dial-peer voice 9202 pots
preference 7
destination-pattern 9T
progress_ind setup enable 3
progress_ind progress enable 8
port 0/1/2
!
dial-peer voice 9203 pots
preference 8
destination-pattern 9T
progress_ind setup enable 3
progress_ind progress enable 8
port 0/1/3
!
dial-peer voice 9300 pots
preference 9
destination-pattern 9T
progress_ind setup enable 3
progress_ind progress enable 8
port 0/2/0
!
dial-peer voice 91111 pots
preference 1
destination-pattern 911
progress_ind setup enable 3
progress_ind progress enable 8
port 0/0/2
!
dial-peer voice 91112 pots
preference 2
destination-pattern 911
progress_ind setup enable 3
progress_ind progress enable 8
port 0/0/3
!
*end C&P*

*start C&P*
# Results Summary

* Calling Party Information
o Calling Party = 3341
o Partition =
o Device CSS =
o Line CSS = CSS Winchester Long Distance
o AAR Group Name =
o AAR CSS =
* Dialed Digits = 9911
* Match Result = RouteThisPattern
* Matched Pattern Information
o Pattern = 9.911
o Partition = PT Winchester 911
o Time Schedule =
* Called Party Number = 911
* Time Zone = Eastern Standard/Daylight Time
* End Device = Winchester-911
* Call Classification = OffNet
* InterDigit Timeout = NO
* Device Override = Disabled
* Outside Dial Tone = NO

# Call Flow

* Route Pattern :Pattern= 9.911
o Positional Match List = 911
o DialPlan =
o Route Filter
+ Filter Name =
+ Filter Clause =
o Require Forced Authorization Code = No
o Authorization Level = 0
o Require Client Matter Code = No
o Call Classification =
o PreTransform Calling Party Number = 3341
o PreTransform Called Party Number = 9911
o Calling Party Transformations
+ External Phone Number Mask = NO
+ Calling Party Mask =
+ Prefix =
+ CallingLineId Presentation = Default
+ CallingName Presentation = Default
+ Calling Party Number = 3341
o ConnectedParty Transformations
+ ConnectedLineId Presentation = Default
+ ConnectedName Presentation = Default
o Called Party Transformations
+ Called Party Mask =
+ Discard Digits Instruction = PreDot
+ Prefix =
+ Called Number = 911
* Route List :Route List Name= Winchester-911
o RouteGroup :RouteGroup Name= WINCHESTER
+ PreTransform Calling Party Number = 3341
+ PreTransform Called Party Number = 9911
+ Calling Party Transformations
# External Phone Number Mask = Default
# Calling Party Mask =
# Prefix =
# Calling Party Number = 3341
+ Called Party Transformations
# Called Party Mask =
# Discard Digits Instructions =
# Prefix =
# Called Number = 9911
+ Device :Type= H323Gateway
# End Device Name = 10.0.3.1
# PortNumber = 0
# Device Status = UnKnown
# AAR Group Name =
# AAR Calling Search Space =
# AAR Prefix Digits =
# Inbound Fast Start = Enabled
# Outbound Fast Start = Disabled
# Call Classification = Use System Default
# Tunneled Protocol = None
# Calling Party Transformations
* PreTransform Calling Party Number = 3341
* Calling Party Selection = Originator
* Calling Party Presentation = Default
* CallerID DN =
* Calling Party Number = 3341

# Alternate Matches

* Note: Information Not Available
*end C&P*

*start C&P*
# Results Summary

* Calling Party Information
o Calling Party = 3341
o Partition =
o Device CSS =
o Line CSS = CSS Winchester Long Distance
o AAR Group Name =
o AAR CSS =
* Dialed Digits = 911
* Match Result = RouteThisPattern
* Matched Pattern Information
o Pattern = 911
o Partition = PT Winchester 911
o Time Schedule =
* Called Party Number = 911
* Time Zone = Eastern Standard/Daylight Time
* End Device = Winchester-911
* Call Classification = OffNet
* InterDigit Timeout = NO
* Device Override = Disabled
* Outside Dial Tone = NO

# Call Flow

* Route Pattern :Pattern= 911
o Positional Match List = 911
o DialPlan =
o Route Filter
+ Filter Name =
+ Filter Clause =
o Require Forced Authorization Code = No
o Authorization Level = 0
o Require Client Matter Code = No
o Call Classification =
o PreTransform Calling Party Number = 3341
o PreTransform Called Party Number = 911
o Calling Party Transformations
+ External Phone Number Mask = NO
+ Calling Party Mask =
+ Prefix =
+ CallingLineId Presentation = Default
+ CallingName Presentation = Default
+ Calling Party Number = 3341
o ConnectedParty Transformations
+ ConnectedLineId Presentation = Default
+ ConnectedName Presentation = Default
o Called Party Transformations
+ Called Party Mask =
+ Discard Digits Instruction = None
+ Prefix =
+ Called Number = 911
* Route List :Route List Name= Winchester-911
o RouteGroup :RouteGroup Name= WINCHESTER
+ PreTransform Calling Party Number = 3341
+ PreTransform Called Party Number = 911
+ Calling Party Transformations
# External Phone Number Mask = Default
# Calling Party Mask =
# Prefix =
# Calling Party Number = 3341
+ Called Party Transformations
# Called Party Mask =
# Discard Digits Instructions =
# Prefix =
# Called Number = 911
+ Device :Type= H323Gateway
# End Device Name = 10.0.3.1
# PortNumber = 0
# Device Status = UnKnown
# AAR Group Name =
# AAR Calling Search Space =
# AAR Prefix Digits =
# Inbound Fast Start = Enabled
# Outbound Fast Start = Disabled
# Call Classification = Use System Default
# Tunneled Protocol = None
# Calling Party Transformations
* PreTransform Calling Party Number = 3341
* Calling Party Selection = Originator
* Calling Party Presentation = Default
* CallerID DN =
* Calling Party Number = 3341

# Alternate Matches

* Note: Information Not Available
 
Upvote 0 Downvote
what might be happenning is you are not matching the right dial-peer, therefore the delay to connect. Debbuggimg your dial-peers should show you which one ypu are using.
Also try this:
On your first dial-peer:
dial-peer voice 9101 pots

add this command:

direct-inward dial

then give it amother shot.
 
Upvote 0 Downvote
well. I did some research and tried adding "prefix 911" to my dial peers that have "destination-pattern 911".
we successfully tested this at each location.
Thanks for all your help.
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

DiyFrea
  • Locked
  • Question Question
called name between avaya I P office & CUCM via SIP trunk
Replies
1
Views
641
DiyFrea
DiyFrea
teknoloji
  • Locked
  • Question Question
CUCM Call Pickup Not Working
Replies
0
Views
440
teknoloji
teknoloji
DTGMI
  • Locked
  • Question Question
Nortel to Cisco VG310 & 4431 SIP GWs
Replies
0
Views
306
DTGMI
DTGMI
larmi
  • Locked
  • Question Question
Calls not queuing
Replies
0
Views
312
larmi
larmi
Ahmed626
  • Locked
  • Question Question
Need to register NEC DT730G on CUCM
Replies
0
Views
341
Ahmed626
Ahmed626

Part and Inventory Search

Sponsor

Back
Top