I'm currently ONLY able to console into this router cause I think it's got a serious problem. This was given to me recently and I am trying to revive it from the dead. Here's the current boot up:
---
TinyROM version 1.4(1)
19:38 11/07/00
Copyright (c) 1998-2000 by cisco Systems, Inc.
All rights reserved.
POST ............ OK. 4MB DRAM, 8MB Flash.
Accessing flash:c800-y6-mw.121-3.XG4
Booting "c800-y6-mw.121-3.XG4" ...,
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C800 Software (C800-Y6-MW), Version 12.1(3)XG4, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC:Home:SW:IOS:Specials for info
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Fri 23-Feb-01 16:05 by detang
Image text-base: 0x000EE000, data-base: 0x00655000
Cisco C802 (MPC850) processor (revision 1) with 43464K bytes of virtual memory.
Processor board ID JAD05020A2H
CPU part number 0x2101
Bridging software.
Basic Rate ISDN software, Version 1.1.
1 Ethernet/IEEE 802.3 interface(s)
1 ISDN Basic Rate interface(s)
4M bytes of physical memory (DRAM)
8K bytes of non-volatile configuration memory
8M bytes of flash on board (4M from flash card)
---
That's it. I know there's supposed to be a config register line and then a router prompt that show. Anyone have any idea why this is doing this? And please, someone tell me what to do besides "Calling Cisco" and "Buy a new one/replacement" cause IF there is any other possible way to fix this I would be glad to try something.
So far I have tried an ios-conf=142 and have tried 'reset' command. I don't have any fresh images to upload into the router. I even opened up the router casing and popped out the chip or whatever it is that comes out and then turned on the router without it to see if it would reset it or something. It does the same exact thing over and over. Seems like nothing is budging.
Thanks so much for any help.
---
TinyROM version 1.4(1)
19:38 11/07/00
Copyright (c) 1998-2000 by cisco Systems, Inc.
All rights reserved.
POST ............ OK. 4MB DRAM, 8MB Flash.
Accessing flash:c800-y6-mw.121-3.XG4
Booting "c800-y6-mw.121-3.XG4" ...,
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C800 Software (C800-Y6-MW), Version 12.1(3)XG4, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC:Home:SW:IOS:Specials for info
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Fri 23-Feb-01 16:05 by detang
Image text-base: 0x000EE000, data-base: 0x00655000
Cisco C802 (MPC850) processor (revision 1) with 43464K bytes of virtual memory.
Processor board ID JAD05020A2H
CPU part number 0x2101
Bridging software.
Basic Rate ISDN software, Version 1.1.
1 Ethernet/IEEE 802.3 interface(s)
1 ISDN Basic Rate interface(s)
4M bytes of physical memory (DRAM)
8K bytes of non-volatile configuration memory
8M bytes of flash on board (4M from flash card)
---
That's it. I know there's supposed to be a config register line and then a router prompt that show. Anyone have any idea why this is doing this? And please, someone tell me what to do besides "Calling Cisco" and "Buy a new one/replacement" cause IF there is any other possible way to fix this I would be glad to try something.
So far I have tried an ios-conf=142 and have tried 'reset' command. I don't have any fresh images to upload into the router. I even opened up the router casing and popped out the chip or whatever it is that comes out and then turned on the router without it to see if it would reset it or something. It does the same exact thing over and over. Seems like nothing is budging.
Thanks so much for any help.
Thanks for the tip Jimmyzz! Only problem is that I don't have a CCO login. Like I said it was donated to me and it's way out of warranty. DOH! Hopefully I can get an IOS somehow or another. It would be a shame to this excellent piece of equipment go to waste. 