3725 will not recognize a atm-t1 8t1-ima card - help (long)?

[madess]

Here is a 2600 I installed the ima card in

Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-JS-M), Version 12.1(3a)T1, RELEASE SOFTWARE (fc1
)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Fri 28-Jul-00 01:41 by ccai
Image text-base: 0x80008088, data-base: 0x81234854

ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)

EXTRA-ROUTER uptime is 2 minutes
System returned to ROM by power-on
System image file is "flash:c2600-js-mz.121-3a.T1.bin"

cisco 2610 (MPC860) processor (revision 0x203) with 59392K/6144K bytes of memory
.
Processor board ID JAD03460973 (2333473716)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
1 Ethernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
8 ATM network interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

ATM1/0 is administratively down, line protocol is down
Hardware is ATM T1
MTU 4470 bytes, sub MTU 4470, BW 1500 Kbit, DLY 20000 usec,
reliability 0/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Keepalive not supported
Encapsulation(s): AAL5
256 maximum active VCs, 0 current VCCs
VC idle disconnect time: 300 seconds
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: Per VC Queueing
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 output buffer failures, 0 output buffers swapped out

here is the show version for the 3725

Cisco Internetwork Operating System Software
IOS (tm) 3700 Software (C3725-IPBASE-M), Version 12.3(5c), RELEASE SOFTWARE (fc2
)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Tue 13-Apr-04 22:22 by cmong
Image text-base: 0x60008AF4, data-base: 0x6102C000

ROM: System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)

btcynosure uptime is 4 minutes
System returned to ROM by power-on
System image file is "flash:c3725-ipbase-mz.123-5c.bin"

cisco 3725 (R7000) processor (revision 0.1) with 121856K/9216K bytes of memory.
Processor board ID JMX0824L3JU
R7000 CPU at 240MHz, Implementation 39, Rev 3.3, 256KB L2 Cache
Bridging software.
X.25 software, Version 3.0.0.
2 FastEthernet/IEEE 802.3 interface(s)
DRAM configuration is 64 bits wide with parity disabled.
55K bytes of non-volatile configuration memory.
31168K bytes of ATA System CompactFlash (Read/Write)

Configuration register is 0x2102

 

[BuckWeet]

You sure that module is supported in the 3725?

you might need to upgrade your IOS to an IP Plus level or such..

BuckWeet

 

[limejudo]

I agree with BuckWeet, make sure the card is compatible with you IOS. I ran into a similar problem last week. It was a compatiblity issue with an adsl wic. Go to cisco.com to find out if its compatible.

 

[madess]

Thank you for the help, a new IOS fixed it.