Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

2821 T1 config HELP pls.

Status
Not open for further replies.

Eitsalo

IS-IT--Management
Joined
Aug 9, 2006
Messages
241
Location
CA
Hi All, I've been trying to get T1 config working but no luck. My command is not accepted from "Config t".
isdn switch-type primary-ni
^
% Invalid input detected at '^' marker.

Here is what I have on 2821:

sh inventory
NAME: "2821 chassis", DESCR: "2821 chassis"
PID: CISCO2821 , VID: V04 , SN: FHK1145F24R

NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot
0", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN: FOC11442V19

NAME: "2nd generation four port FXO voice interface daughtercard on Slot 0 SubSl
ot 1", DESCR: "2nd generation four port FXO voice interface daughtercard"
PID: VIC2-4FXO , VID: V03 , SN: FOC13371WEA

NAME: "PVDMII DSP SIMM with three DSPs on Slot 0 SubSlot 4", DESCR: "PVDMII DSP
SIMM with three DSPs"
PID: PVDM2-48 , VID: V01 , SN: FOC11372FMC

NAME: "PVDMII DSP SIMM with four DSPs on Slot 0 SubSlot 5", DESCR: "PVDMII DSP S
IMM with four DSPs"
PID: PVDM2-64 , VID: V01 , SN: FOC110731WT

NAME: "AIM Service Engine 1", DESCR: "AIM Service Engine"
PID: AIM-CUE , VID: V03 , SN: FOC12260L73


Camoroz2821#

ip interface brief
Interface IP-Address OK? Method Status Prot
ocol
GigabitEthernet0/0 unassigned YES NVRAM up down

GigabitEthernet0/0.22 192.68.27.2 YES NVRAM up down

GigabitEthernet0/0.122 192.68.127.2 YES NVRAM up down

Service-Engine0/1 192.68.127.2 YES TFTP up up

GigabitEthernet0/1 unassigned YES NVRAM administratively down down

Camoroz2821#

T1 will be used for voice traffic with bunch of DID only. This is my first time trying to get this work. Appreciate all your help and I have a dead line to make this working.
Please help.
Thanks in advance.
 
Can you share some of what you have configured? T1 controller config?
 
None, please let me know what command I should use for the out put. If I type sh controllers, the output is very large.
Thanks.
 
If you type isdn swtich-type ? what options do you got???

CCNAV, CCVP
Caos is the natural order of things...
 
show controllers T1
will limit your search.
Post a show run
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top