2801 cannot get to internet

[navsol]

I have a 2801 that I configured with SDM. This is my 1st Cisco router and I have been reading alot, so much I think I have Dain Bramage. Below is my config from the router, can anyone tell me what I am missing. I am trying to get it to the internet, so I can eventually setup up several VPN connections. Thanks in advance.

!This is the running config of the router: 10.10.11.93
!----------------------------------------------------------------------------
!version 12.3
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
!
hostname navsol
!
boot-start-marker
boot-end-marker
!
security authentication failure rate 3 log
security passwords min-length 6
logging buffered 51200 debugging
logging console critical
enable secret 5 $1XXXXXXXX.
!
username nXXXXl privilege 15 secret 5 $1XXXXXXX
clock timezone PCTime -6
clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
no aaa new-model
ip subnet-zero
no ip source-route
ip cef
!
!
ip tcp synwait-time 10
!
!
ip ips po max-events 100
no ip bootp server
ip domain name navigationsolutions.com
ip name-server 64.XXX.XX.90
ip name-server 64.XXX.XXX.138
ip ssh time-out 60
ip ssh authentication-retries 2
no ftp-server write-enable
!
!
!
!
!
!
!
!
interface FastEthernet0/0
description $FW_INSIDE$$ETH-LAN$$INTF-INFO-FE 0$
ip address 10.10.11.93 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
ip route-cache flow
duplex auto
speed auto
no mop enabled
!
interface FastEthernet0/1
description $FW_OUTSIDE$$ETH-WAN$
ip address 68.XXX.XXX.105 255.255.255.224
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly
ip route-cache flow
duplex auto
speed auto
no mop enabled
!
ip classless
ip route 0.0.0.0 0.0.0.0 FastEthernet0/1 permanent
ip http server
ip http authentication local
ip http secure-server
ip nat inside source list 1 interface FastEthernet0/1 overload
!
!
logging trap debugging
access-list 1 remark INSIDE_IF=FastEthernet0/0
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 10.10.11.0 0.0.0.255
no cdp run
!
!
control-plane
!
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
!
line con 0
login local
transport output telnet
line aux 0
login local
transport output telnet
line vty 0 4
privilege level 15
login local
transport input telnet ssh
line vty 5 15
privilege level 15
login local
transport input telnet ssh
!
scheduler allocate 20000 1000
end

 

[examples20001]

Try configuring the default route to your gateway router address (68.XXX.XXX.10X).

Remove "ip route 0.0.0.0 0.0.0.0 FastEthernet0/1 permanent".

Hope this helps.