Search results for query: *

You are right sorry about that :) DONE ! Also - in case anyone is interested, you can drill out the rivets on a Cisco 1711 (they have the WIC-4ESW riveted in non-removable WIC) and use this WIC in a Cisco 1721 (same part # etc). I personally did not have to do this (I just dont like the idea...

Thank you all for suggestions. It was definately an IOS issue I did get it working by using: c1700-sy7-mz.123-7.XR7 Did some more digging on the WIC-4ESW and found some notes that stated it required an X version of IOS in the 12.3 train (prob when Cisco implemented driver support for the...

Hello, I'm trying to get a WIC-4ESW to work in a Cisco 1721 access router. From what I have read the WIC-4ESW is a supported WIC module however it seems to be very IOS specific. Can anyone who is running this setup tell me what IOS ver they are running? I've tried a few vers so far and...

maczen - Thank you for the tips. You had asked about the type of VPN that this is doing, and it is a site to site setup (not for remote users w/ vpn client). The far end device that the NS-25 is terminating VPN tunnels to is a NS-204. Also we are not using an NMS (NetScreen Manager) we are...

Hello, I am working on an issue involving troubleshooting the Netscreen NS-25 providing VPN service for SCTP protocol. We are having an issue where we are seeing SCTP dropping communication to far end partner however I am not seeing any of that in the Netscreen. What is the best debugs to...

Thanks for the response, but I do not understand why. The IP's that I am handing out for the VPN pool are 192.168.1.230-240 which is in the same subnet as the local LAN (int FE0/0 is 192.168.1.1/24). Other reason I do not understand why the VPN pool range has to be excluded from NAT, is...

Hello, I recently setup Cisco IOS VPN and I am having some trouble. I am able to get remote VPN clients to successfully connect and get an IP address however they can not communicate with anything across the tunnel. Also I checked the router running VPN IOS and there is an "Incomplete" mac...

I am going to try it in a lab in the next week I will post my findings. -Rainman

Hello I have a question regarding the Cisco 5814/7206 NAS. The 5814 dial-shelf controller (DSC) is connected to the 7206 via a dial-shelf interface (DSI). This connection is ethernet-based even though Cisco calls it a proprietary DSI connection. When you do a "show dsi" to look at the...

No, when I say "stack" i merely mean a "group of switches connected together and the links are configured as trunks"... definately not using Cisco stacking technology.. Any other thoughts? Will a port-group work on this instance if both links going from the router to separate switches in the...

brianinms - Thanks for your reply. What if both GIG ports went to separate switches tho (both dot1Q trunk links within same switch cluster). Also what about the possibility of doing bridging (IRB)? How does IRB react to dot1Q trunks, and can a BVI interface accomodate for sub-interfaces...

Hello, I have a situation I am troubleshooting where we have the following scenario: [router] --- dot1q trunk--- [switch] -- [other switches] Basically I am doing router on a stick (I have sub-interfaces on the router's interface facing the 1st switch. The issue I am having is if we have a...

Hello, Is there any way to have the Cisco IOS send a syslog trap when IP POOL utilization gets low (i.e., a set threshold)? Besides the IOS being able to send info regarding pool utilization, is there any commonly-used 'nix scripts or anything readily available to handle managing IP pool...

You need a 10/100 interface to do trunking. 10mbit is not enough to carry the inter-trunk messages thus Cisco did not enable trunking for anything below 100mbit LAN interfaces. -Rainman

What type of DS3 port adapter are you using? Usually clear-channel DS3 interfaces do not have a "controller T3". Only time I have seen "controller T3" on a Cisco device is when it is a Multichannel DS3 port adapter which can not do clear channel functions. Try this: config term ...

Hello, I am in a troubleshooting situation regarding a few Cisco AS5800's running IOS version 12.3(10). There are channelized DS3's conn'ed to the AS5800's to support incoming dialup modem calls over the T1 channels. I have noticed alot of syslog messages that state T1's are dropping, in...

Hello, I'm working on turning up two Cisco 76xx's and they are interconnected via GIG-E. I'm going to do routing between them (this is just my overview of the goal).. In between that GIG-E I am also turning up the optical transport gear... Ciena 3600's via oc-48 and mapping eth ports across...

Here is the configuration I use on a 6509 w/ SUP2 and MSFC2: Layer 3 MSFC2 config (IOS): config term ! ntp server 1.2.3.4 ! end Layer 2 SUP2 config (CatOS): #ntp set ntp client enable set ntp server 1.2.3.4 Hope this helps! -Rainman

Hey guys thanks for the suggestions. I went ahead and started moving the modules around and the modules are now active. Seems when I was trying to run the 4-port T1 and 1-port DS3 module, it would only work if i had the T1 module in slot 1, and the DS3 module in slot 2. If i swapped the...

Hello, I am trying to configure dot1x authentication on a Cisco 3550. I have read up on the configuration and it seems easy, however every configuration I have read shows the authentication method pointing to a RADIUS server. Has anybody ever set this up using "local" authentication with a...