Search results for query: *

Hi Zastruga, There are two generations of IP DECT: DECT R3 - older generation, base stations are RFP32, RFP34 DECT R4 - current generation, base stations are IPBS So my question was: is R3 compatible with CM6, CM7 ? Thank you in advance, The Curious

Seems that nobody knows.... The Curious

Hi folks, Is DECT R3 system compatible with CM6 or CM7 ? My customer has large DECT R3 installation on CM4, and thinks about upgrade to CM6 or CM7... Best regards, The Curious

Hi Ceejay, Good point, but unfortunatelly it cannot be used in this case. When I call extensions located on ELU-A: - If I call from analog extension - call is rejected - If I call from digital extension - call is immediately parked on line 1 So, there is no ringing period at all, voltage...

1. List all abbreviated numbers (short numbers) ADCDP:ABB=ALL; 2. Delete all abbreviated numbers ADCOE:ABB=3XXX&&3YYY; 3xxx is the first abbreviated number, 3yyy is the last one 3.Number analysis: remove 3 as abbreviated number prefix NANSE:NUMTYP=AC,NUMSE=3000&&3999: 4. Assign prefix 3, as...

Hi folks, Is it possible to find out if ring generator on ELU-A is working or faulty ? Would any tracing, warning logs or extension supervision from BMS show anything if ring generator is faulty ? In my case BP50 behaves like this: Extensions from ELU-A can call digital extensions. Digital...

Tak Doktor The Curious

OK Doc, So you had the same BRI problem with MD110 and solved it by grounding the PBX ? The Curious

OK Goldstar Doktor, I will try to improve the grounding, but I suppose that it will not solve the problem. What I had in my mind is software solution. From my experience I know that BP250 systems never have problems with BRI ISDN, and MD110 are very sensitive to BRI errors. What is your...

Hi folks, I have an installation where BC12 SP6 system is connected to ISDN BRI lines via TLU79. ISDN lines have bad quality, and there are lot of alarms which appear and disappear in a short time (local telecom claims that "everything is fine" with their lines). Alarms are: 269 DIGITAL TRUNK...

CM4,G650/S8720, H.323 IP phones - models used are 4610 and 4621, computer network is based on Cisco 3750 switches. Customer run out of ports in ethernet structured cabling, therefore they connected a cheap, non-managed switch to PC port on IP phone. 4 computers are connected to non-managed...

Thanks Tier 3, I already went through this documents, all of them are based on replacing a faulty flash disk. I was looking for workaround, in order to avoid changing flash disk. Now I understand that workaround does not exist. I contacted Avaya, official information is: 2Gb system flash disk...

Hi Tier3, Thanks a lot. I have some old flash card backup, so it will not be a complete disaster if I shut it down.. Modem access and saving translations - sounds nice, how can I do that ? The Curious

S8400 Server / G650 gateway / CM4.0 Save translation command does not work, response from system: MSS Error Encountered It is not possible to access server from web interface. As far as I know, this should be a problem with flash disk on S8400 board. There is special patch that tells you if...

d=1 to turn on music on hold d=2 is a special case, music on hold is turned on only if you have RVA in your system. (RVA = recorded voice announcement, there is special board for that purpose) The Curious

OK MDTAREQ, If you have, for example, 4 people in a hunt group: - first four calls will be answered by your people. - fifth call goes into que and listens to music, announcements, whatever you use in your system. Fifth caller waits for any of your people to become free. If QUE=0, and all 4...

GHGRI create a hunt group SERV=11001 1 hunt group is open for DID traffic 1 no recall provided when operator extends call to hunt group 0 doesn't matter 0 no music-on-hold 1 Brazilian collect call system allowed TRAF=15 calls to hunt group are allowed to all users of PBX SEL=112000 1 Search...

Noone knows ?? The Curious

Hi people, I have a customer with CM4 system, having old IP DECT ( RFP32 base stations, 3701 and 3711 handsets). Is it possible to upgrade this PBX to CM6 and keep the existing DECT system ? Best regards, The Curious

Hello Van Zenden, Thanks! I changed Outgoing Display to Y, and redial is working now. But this has generated another problem, when users call some telephone number it is not shown on the display any more, just "Public ISDN ARS" .... Best regards, The Curious