Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: f2b
  • Order by date
  1. f2b

    Site-Site VPN works on one subnet only!

    Hi all Have set up Linksys-Linksys VPN successfully and works great using two model AG241's. The remote site has two subnets. Setting up with one subnet works and all is well. As soon as I change the "Remote Secure Group" to "Any" or 192.168.0.0, I cannot see the remote site, although the VPN...
    • f2b
    • Thread
    • Replies: 0
    • Forum: Modem
  2. f2b

    Does Anyone use a Packet Shaper?

    Thanks guys for your valued advise. Much appreciated.
  3. f2b

    Does Anyone use a Packet Shaper?

    We have also been looking for something like this. However, I recently upgraded one of our 4100's to v4.0.0.2 It was mentioned that QoS can now be done at the application level. A packet shaper is supposed to provide QoS, compression and acceleration. How does the Sonicwall compare...
  4. f2b

    4.0.0.1 officially released

    Thanks for the prompt. Looks like 4.0.0.2 is now on General release, for the 4100 anyway.
  5. f2b

    Dell Powerconnect

    Hi Can anyone tell me if these switches are reliable. Currently we are using HP procurve switches and the powers above want to get these switches from now on for new sites and add to the existing network to cut cost. I think this may be fals econmy, but having said that I don't know much about...
  6. f2b

    ADSL load balance question

    A little late I know, but thanks guys for your input. Much appreciated. Thanks A
  7. f2b

    linkling up several 2650's...how best?

    Thank you for the advice
  8. f2b

    linkling up several 2650's...how best?

    Thanks, it certainly does. Because we are using voice and data on two vlans would the core switch need to be something like a 2824 as this is POE and 24 x 1Gb ports? 6 2650's are dedicatyed to voice and the other 6 for data only. Plug all 12 into the 2850, but after this I am unsure about how...
  9. f2b

    linkling up several 2650's...how best?

    Ok we have an office argument, which I hope you guys can clear up. On this perticular site we have 12 procurve 2650's and all are cascaded off each other via the 1GB uplinks. All switches have 2 Vlans. Vlan 1 is for data and the 2nd vlan is for IP telephones. All seems to be working ok. Is...
  10. f2b

    ADSL load balance question

    Ok, lets call is load balancing as that is really what I am after at the end of the day. Ie, making user of 4 x 7Mb ADSL's. If load balancing only gives you 7Mb out of a total of 4 x 7Mb ADSL's then why are Cisco providing this. I mean what's the point? We are based in Spain with Telefonica so...
  11. f2b

    ADSL load balance question

    Yes, that is what I ment. Making use of all 4 ADSL's. I heard somewhere that it will only work in one direction and I think it is downstream. So uploading will still be at around 700kbps? How would the other end know what to do with the packets. For example, if the ADSL's are on different...
  12. f2b

    ADSL load balance question

    Hi Load balancing using a 2800 with 4 x wic ADSL cards. How does the load balance work? For example if we have 4 x 7MB ADSLs (7Mb downstream, 700Kb upstream). Would this then mean around 28Mb downstream and around 3Mb upstream? I cannot imagine how the packets would get to their correct...
    • f2b
    • Thread
    • Replies: 8
    • Forum: Cisco
  13. f2b

    DSL Router/Firewall Solution needed

    Hi We need to change 10 of our office DSL routers from the standard ISP ones to something that can be a Broadband router and have a reasonable firewall all in one box. Cost per router no mor ethan 200 Euros Any suggestions? Thanks
    • f2b
    • Thread
    • Replies: 0
    • Forum: Modem
  14. f2b

    Mitel 3300 issues with 2nd IP subnet

    Well, the phones get their IP address from the 3300, which is 192.168.48.0 range. Prior to intrioducing the .55 range, the phones used to look at the .47 range then get a .48 address and load up ok. Now, if a phone re-boots, it gets a 55.0 address and hangs. This range works ok for pc access...
  15. f2b

    Mitel 3300 issues with 2nd IP subnet

    The phones are just hanging on the new subnet and not getting further. Ie, not picking up a voice (48.0) range. 3300 is running version 7.1.3.6 Thanks
  16. f2b

    Mitel 3300 issues with 2nd IP subnet

    Hi We have two VLAN's. Default VLAN 1 for Data (192.168.47.0)and VLAN 10 for Voice (192.168.48.0). All ok until we added an 2nd Data subnet (192.168.55.0) to the HP switches on the Default VLAN 1. Now some of the phones are picking up the new range and then getting "TFTP error packet send"...
  17. f2b

    HELP. Deleted partition on USB Flash Drive

    Hi Rebuilt my pc and forgot the USB flash drive was still plugged in as I backed my documents onto it. I then accedintally deleted it's partition thinking it was the C Drive. Rebuilt the PC and only noticed it afterwards when I tried to restore it. How can I recover the UDB drive partition...
  18. f2b

    Cisco 871 start config

    I'm looking at the router and it is definately an 871. Also, it has 4 LAN ports (FE0 to FE3) and a WAN port (FE4). The ADSL cable is plugged into the FE4 port, which says "WAN". Thanks
    • f2b
    • Post #10
    • Forum: Cisco
  19. f2b

    Forwarding ports to anotrher subnet

    Hi AG241 (192.168.5.1) is connected to a firewall wan port on 192.168.5.2/24. The firewall LAN port is 192.168.40.0/24 and also has another subnet 192.168.45.0/24 - both subnets are routed to the wan port and work for internet ok. I need to VNC to machines on both subnets externally. The two...
  20. f2b

    Cisco 871 start config

    Ok, I think I've configured properly now. The WAN link light does not come on. Works on a Linksys. I cannot see how to tell the Fastethernet4 (WAN) interface the VPI and VCI (8/32 for Spain). Using SDM does not show this either. Can anyone help? Thanks Andres

Part and Inventory Search

Back
Top