Search results for query: *

My 450-T fail to come up after power restart. On console is shows ASIC BUFFER RAM TEST ...... Fail all other test are pass I can do any thing on Console also. It stops at Self-test detected a failure 00000000 Press RETURN to continue Front panel LEDs are Blinking. IS the Device is Dead? Need...

Thats correct, but it will give u only one channel. If tommorow u need to access the second channel then u have to delete the all dial and port config. As I have gone throug Nortel Doc- nowhere it metion about the channel. You can on Dial-demand/Backup-demand specify channel-count 1, so it will...

Hi Guys, How can you access individual channel on BRI port on ARN as in Cisco you can specify bri1/1:0 or bri1/1:1 I have checked BCC also but of no use. When you specify Demand circuit it shows only Channel count 2 -Mohi

Hi, I am looking for WIN2K Pro. VPN problem. My setup is: Client==Internet===VPN===Internal LAN All my servers on LAN are running WIN2K in mixed MODE, with "ABC"(Pre-W2K Domain) and "XYZ.COM"(W2K domain). All Services are Running WINS,DNS,DHCP. Problem: Win2K pro...

Hi, I am looking for WIN2K Pro. VPN problem. My setup is: Client==Internet===VPN===Internal LAN All my servers on LAN are running WIN2K in mixed MODE, with "ABC"(Pre-W2K Domain) and "XYZ.COM"(W2K domain). All Services are Running WINS,DNS,DHCP. Problem: Win2K pro...

hi, Disconnect the routers . Put the flash. Reboot the router . Press the break Key. At the ROM mode type: bconfig image local bconfig config local reboot it u r Done

I suppose MTU for CISCO is 1600 not 1518

Hi, Use site manager to configure the link. What Kind of encapsulation is at the ISP side? is it PPP or HDLC or Frame-relay whatever. Just Check with the ISP. -bhandari

Hi, Can you paste cisco config. -bhandari

Hi, ONCE PACKET LEAVES THE ROUTER , FRAME-RELAY Switch it looks for DLCI Number . Frame relay switch switches the DLCI and forward the packet to destiend Interface. -bhandari

350 Needs IP address only for management. For default config it is Plug and Play. Do you have any MDA module?? if not Connect two switches with Crossover cable. -bhandari

use wildcard like suppose you have range from 192.168.32.16-31 then 192.168.32.16 0.0.0.31 Method: set mask to "0" upto where you want match and "1" for the range. in my case 16=10000 31=11111 so 16-31 mask will be 00011111=31 first 3 octats will be 0.0.0 as thay...

Hi Mike, Regarding back-to-back Frame-relay link it not required to have 3rd router. You can connect them with DTE & DCE cables. How? Check this out http://www.cisco.com/univercd/cc/td/doc/product/access/multicon/3810soft/swcfg/vofrcfg.htm#xtocid1474315 -bhandari

Goto and play presentations http://www.webtorials.com/ -bhandari

Mark it seems now that you have Driver/Ethernet, since you are unable to ping in between. Hybrid and Broadcast these are used for name resolution. I feel you should not worry about them right now. -bhandari

Hi Folks, Let put some thought. Network Scenario: >R3----R1======R2-----R6< | | ^ | | | | | R4-----|-------| | ^ |-------------R5< R1 & R2 Core router in Area 0 R3,R4,R5,R6 are ABR &quot;>&quot; show totally Stub Areas. Q1...

Hi, it seems diagram is little bit distorded. To understand do a cut and paste in reply window and shift R4 till it come under R3 by pressing del key, adjuest other row accordingly. -bhandari

Hi Folks, Let put some thought. Network Scenario: >R3----R1======R2-----R6< | | ^ | | | | | R4-----|-------| | ^ |-------------R5< R1 & R2 Core router in Area 0 R3,R4,R5,R6 are ABR &quot;>&quot; show totally Stub Areas. Q1...

Hi, Run winipcfg ,on both pc both should have 1. same subnet mask something like 255.255.255.0 2. ip address should be same upto three decimal or where the last 255 end. as if subnet mask is 255.255.0.0 , both ip address should be same upto 2 decimals. check cross cable pinout 1-3 2-6 -bhandari

Check you might have configerd the PPP multilink.