Search results for query: *

I think I had the same issue last week. I logged in to the Primary SS using SSH - I got in OK. I did an isetShow and found that TPS was still working (Half the IP sets were registered on it). The disTPS command migrated all idle sets to the Secondary SS. I kept doing isetShow until all the...

Each ICI key can only have one route. The ICI keys mean the Attendant can see which route an incoming call is on. They can answer the call by pressing the ICI key. It gives the ability to choose which route to answer, if there are multiple calls coming in.

IP500 V2 with IPO8(44) in the UK. I want to bar a group of extensions from dialling ALL external numbers EXCEPT: Calls to local numbers 901234xxxxxx 914101234xxxxxx 95xxxxx 92xxxxx 91415xxxxx 91412xxxxx Calls to emergency services 9112 9999 9141112 9141999 Can somebody give me a definitive...

Thanks Hairlessupportminkey - that will keep the UK Civil Aviation Authority happy Laurence

Can anybody help me find Mean Time Between Failure (MTBF) data for IPO 8 with a Control Unit, 2x POTS 16 Expansions and 2x Digital station 30 Expansions? I can't seem to find this on the Avaya site TIA Laurence

You will need "ftr cfw 12" AND "ftr dcfw 12 xxxxxxx

Check your IP route between sites. If I remember correctly the voice channels show idle even when the ethernet cable is disconnected. The D channel stays up too. Try pinging the far end system in LD 117

I use the freeware PDF generator at: www.primopdf.com I've never seen it fail. Regards Laurence

Go to http://support.nortel.com/go/main.jsp?cscat=DOCUMENTATION&poid=15181&viewOptSelect=5|null Then download the task based guides: Business Communications Manager 50 (BCM50) - Release 3.0 Task Based Guides - zip Archive Check out the IP Telephony section Laurence

Have you checked the TARGs/TGARs for the routes involved?

I think the problem is, SIP endpoints need to "see" each other directly. It works fine within the same subnet on a switched-only network. Routing between subnets causes a problem. This is a problem with SIP, not with Nortel hardware.

You only need to set the DIP switches on a GATM module. The settings are country-specific.

Try the VOIP lines in pool BlocA

Yes, and OTM has had no problems since it was installed in May 2003. The problem only occurred this week. It looks like corruption somewhere.

A customer has an Option 61C, 25.40B with Meridian Mail 12.12. There are 500+ TDM sets on the system. He uses OTM 2.00 for sets admin. He modified a 2616 in OTM, to add an "MWK 7000" key. There are many 2616's with the same feature on the system. Just when he entered the Mail DN, OTM reported...

As BIV343 said, check the d channel messages on the M1. This will show the actual digits sent from the M1 to the BCM. To switch it on in the M1: LD 96 ENL MSGO X (where X is the d channel number) To switch it off: DIS MSGO X Make a call and watch the messages Set the recieved digits on the...

Scuba, As the guys said, Use ld 81 to find an unused group number. Then use ld 20 to add each set to the group: REQ chg TYPE (500, 2616, 3904 etc) TN x x x x ECHG yes ITEM rnpg y (y is the group number) ITEM <cr>

Skippy, DPNSS is a signalling system used on T1/E1 PRI links here in the UK. Not being cheeky, what's a KSU? Laurence

Hi I have inherited the maintenance of a very remote Coastguard Modular system which is linked to another switch using DPNSS. The guy who set it up retired and didn't know much about it anyway. He was talked through the setup by someone on a phone call. Can anybody send me a recipe to setup...

Have you tried <ctrl> r to refresh the screen?