Search results for query: *

Hello, Have a LDK 100 with a faulty 12 port SLT card (SLIB2e) I've got a spare GDK 100 "SLIB II" card, which I think is 12 port SLT. Is this card compatible with the LDK 100? if so what code should I use for it in PGM 101? (I don't see this specific model card in the manual) Thanks for any help.

Sorry doktor, I'm thinking of 4-10. Got mixed up for a minute there - ignore the above post. I'll have a look at 10-4 when I get the chance, anything in particular I should be looking for or is it pretty self explanatory?

Yes, 10-4 is where I've been looking. All the destinations (10-4-2/4) and DDI numbers (10-4-6) are setup and working great. I just wondered if it was possible to add a name/tag to the numbers to display on incoming calls? I can't see anywhere for this within 10-4.

Thanks, I'll have another look tomorrow, though I'm pretty sure flex key 6 was where the actual telephone number was entered (I don't remember seeing anything about names)

Is there anyway to set a name for lines/DDI numbers, so it displays on the handset on an incoming call? DDI's are setup in the the MSN table (4/10) and work fine but I couldn't see where a name would be added. Thanks :)

Hi obtsystems, Tried that today it it all worked okay, thanks for the help.

Maybe you could create a SIP extension for each PSTN line on the NS500 then tell each line to go to their respective ext (eg Line 1 > Ext 200, Line 2 > Ext 201 etc.) Then using the settings for these extensions go to your Elastix box and create a SIP trunk for each one. Then when a call comes in...

Hi All, I've been working on a old Panasonic KX-TD1232, setting up/installing some additional extensions and doing some general programming. I have been asked if I could connect the system to their PA system, which is situated about 8 metres from the 1232 in a room the floor below. Admittedly I...

Hi snowman50, Thanks for the reply. I am hoping to go onsite this week and I'll give your instructions a go. I've found out today that the system had a level 2 reset and therefore is pretty much not programmed for anything! Do you have any advice on what order to do things? It has 11 IP phones...

Hi All, Can anyone tell me how to set up 1 circuit (2 channels) of BRI ISDN2 on a BCM50? I can't seem to see where to start in the Elements Manager software. System comprises of BCM50 main unit, a MBM with the BRIM module. I have enabled the module and it says it's enabled but I'm not sure...

Sorted it, BT431A to RJ11, 1-3, 2-4, 3-1, 4-2 Regards, Del

Hi All, I have a Panasonic KX-T206 system and a KX-T7130E handset that is missing the line cord, I have tried various spare cords but none appear to work so I have decided to make one up but can't find the pinouts for the RJ11 to BT Plug, I'm guessing it's a six wire one. Does anyone know what...

Thanks to everyone for all the help, I'll try to get BT to change the disconnect clear time to 800ms. If not maybe I'll have to consider ISDN2e lines. Regards, Del

Same thing happens if the extension doesn't get answered and I leave a message. It seems like it has a set amount of time for the mailbox to run. I have looked in the mailbox settings in the menu block but I can't see what might be causing it. Any help is appreciated. Regards, Del

OK, I set the line to go to ext 201 therefore bypassing the AA and it hangs up immediately so I believe the problem is in the SVMi-20E settings. I watched the port activity when I called in and it appears to be going to voice mail after I hang up. So the line stays busy. Regards, Del

Hi CatOnKeyboard, I have sorted most of it out except when I call in and choose any option eg. press 1 for sales it rings the correct extension but if I hang up before it is either answered or goes to voice mail the extension will continue ringing for 3 rings and the line light stays on for 90...

I have already recorded over 1001 because I thought that by defaulting the SMVi and the OS7200 they would come back but they haven't! So is there a way to get this prompt back to the original Samsung one? I've sorted out the other stuff by doing what you said. Regards, Del

Hi All, I have just installed a Samsung OfficeServ 7200 which I have programmed and got working fine except for the voice mail and auto attendant which is using the SVMi-20E module. I have logged into the SVMi-20E and set the AA menu up so that 1 goes to Ext201, 2 goes to Ext204 and 3 goes to...

I have the Manager E software but no lead (yet) do you know the pin outs for the lead? Once I have connected to it will I see the IVM settings? Because when I run Manager E without a connection I can1t figure out where the IVM settings would accessed from. Thanks for your help. Also there...

Hi All, I have a customer with 2 offices that have Panasonic KXTD systems who have just taken over another business (now their third office) that has a Siemens HiPath 3550 and the auto attendant has 5 options which they want to reduce to 3. My Siemens experience is limited to the older Office...