Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. johnPlayer1

    CO LINE SETTING

    Thank you for the elaboration. This was the solution to my problem. I used the QTT feature. Thank you CMUK Obtsystems Ired1980. Stay safe everyone.🙂 ~johnPlayer1
  2. johnPlayer1

    Panasonic upload problem

    The issue has been resolved. Thank you for all the reply. Let's all stay safe.🙂
  3. johnPlayer1

    Panasonic upload problem

    Thank you for the reply. 🙂
  4. johnPlayer1

    CO LINE SETTING

    thank you for the reply. yes, the co lines are analog. when connected directly with a standard phone. the line times out when caller hook-on the phone. here is a view of the set up: CO line (call) ---> [PABX (configured features: DISA-ICDG-DIL)] ---> operator before, outside calls with DISA...
  5. johnPlayer1

    Panasonic upload problem

    Thank you Ired1980. I will try to use to clear button.
  6. johnPlayer1

    CO LINE SETTING

    Thank you for the reply. I have a reply a while ago but i'll revise. it was vague. [peace] I've concluded that the CO line was the problem but after going through the reply of CMUK. and going through the process of the call. I thought what if it's not the CO. so: Is there a setting in kx ns300...
  7. johnPlayer1

    CO LINE SETTING

    Hello! Again😁 Is there a feature on kx ns300 where i can configure the CO line? The CO line is disconnecting prematurely when no answer like 30 or 40 sec. Thank you! Stay safe everyone! -john
  8. johnPlayer1

    Call huntimg group

    Thank you obtsystems. 🙂That is what is lacking in the config.Got the system working as required. Stay safe everyone.🙂
  9. johnPlayer1

    Call huntimg group

    Hello! I hope everyone's safe🙂 Can anyone please help me with the following: System: kx ns300 602: ext.: 201, 202, 203 603: ext.: 201, 202, 203 1.) When caller connect to 602 from DISA ext. 201 should ring first, then 202, then 203 after 5rings. 2.) When caller connecta to 603 from DISA ext...
  10. johnPlayer1

    Panasonic upload problem

    Thank you Mike. I checked the file it was .wav(mono) so iwent over my notes.. 🤦‍♂️My bad, i was uploading the ogm file to "file transfer pc to pbx" when i should be uploading it to "message file transfer pc to pbx." I'm uploading it for DISA. Fyi to my fellow noob😅✌. I would like to ask...
  11. johnPlayer1

    Panasonic upload problem

    Hello. Help please.. 🙂 I was trying to upload a .wav for ogm but i got the error "this file cannot transfer from maintenance console". The wav file is less than 1mb and less than 1min. Any advice please? Thank you in advance!🙂
  12. johnPlayer1

    PANASONIC KX TDA 200 TROUBLESHOOTING

    Yeah, i did put back the cards.. reset and restore. Cards and pbx is working again. ☺ The slc card that was "dead" from the start was the only one with no changes. Maybe it already needs replacement. Thank you very much to you all. Keep safe!
  13. johnPlayer1

    PANASONIC KX TDA 200 TROUBLESHOOTING

    I checked all the fuse with a multi tester. All of them have continuity. Are there other options how can i check the cards if possible? How often does the main board of the KX TDA 200 get damaged if anyone knows? The system I'm trying to fix been running since 2007. Please bear with me I'm...
  14. johnPlayer1

    PANASONIC KX TDA 200 TROUBLESHOOTING

    thank you Mike. will do check the voltage on those points. If there are problems in the control points. should i let the board fixed or replace it with a new board?
  15. johnPlayer1

    PANASONIC KX TDA 200 TROUBLESHOOTING

    Hello! Can you please help me how should I start to troubleshoot the PBX shown in the image. By the way SLT card #6 light is off ( i think it's a dead card). Thank you in Advance. Keep safe everyone!
  16. johnPlayer1

    Panasonic KX-TDA200 Additional CO and Restarting

    Thank you omonat! My wiring of the LCOT was right then. I will connect it again. I removed the new CO line thought the red lights were posing a problem after the connection. The red lights got me worried after they flashed "longer" than expected. But as you said it gradually turned green as it...
  17. johnPlayer1

    Panasonic KX-TDA200 Additional CO and Restarting

    Hi, Can anyone please advice me about the following: I'm trying to add a new CO on a running tda200 is it possible? I tried connecting the new CO(from modem) directly to the PBX but i think a restart will be needed for the new CO to work? When i tried to restart the pbx it took like more than...
  18. johnPlayer1

    Cloning windows 98 hard disk

    I used acronis to clone a windows 98 system before. the clone was hdd to hdd. the disk was cloned as is. the clone will work just fine if you will plug it in a new system unit. but you will need to update on the drivers if they have different hardwares.
  19. johnPlayer1

    PANASONIC KX-NS300 ringback configuration

    @obtsystems thank you for your reply. yes they are analog trunks I will work around that option. I will update the thread on what will happen. thank you.
  20. johnPlayer1

    PANASONIC KX-NS300 ringback configuration

    Hello! Sorry I'n new to this. I need some help from your brilliant minds :) Is there a way to set the timer on the trunk ringback of Panasonic kx-ns300? I'm trying to adjust the trunk ringback to ring once before the Auto attendant plays. I've set the "Delayed Answer Timer(s)" to "0". Now...

Part and Inventory Search

Back
Top