Search results for query: *

Thanks guys but all is now well , waited a short while and they then semed to work ok !!! Strange. Thanks anyway Mucka

Hello Guys , we have a large network of 14 X 8600,s with a large overhead of routes using ospf . Does anyone know of any documents/white papers on route summerization that may help me with this . Thanks in anticipation Mucka

Hi guys I have set up successfully a series of filters on Passport.The problem is trying to let one lan communicate with another ie: desination of 10.10.14.0/24 to source of 10.10.28.0/24 forward, to enable pc,s on one side (28) to print to a printer on 10.10.14.0 network.Very simple and...

Hello guys , we are running the above switch manager ver3.0.0.0 when upgrading firmware to our BPS,s we put in our bossXXXX.img and works a treat ,BUT how do we upgrade the diag file ie: boss3005_diag.bin. ?? We tried it in the image field but doesnt work and tried it in the "450/mix stack"...

Thanks biv343, can anyone suugest a later stable code ver that may correct this web browsing fault ?? Thanks again Mucka

Hello all , has anyone seen this fault ,very infrequently we have a loss of "Trusted Ports " after a power outage ,resulting in bad voice quality . We do not have a config loss , just Qos advanced ->interface conf->Trusted ports loss. The vlans & ip etc are all ok . Has anyone else seen this .We...

Hello Hungryhouse thanks for the reply yes we need to keep our default route 0.0.0.0 nxt hop X.X.X.X . Then certain sources in our large routed network need to get to the internet via a seperate isp, so yes FROM 192.168.0.0/16 nxt hop Y.Y.Y.Y .We have 400 vlans and routing via 13 X 8600,s so all...

Hello all , we have a default route on our main passport to our internet connection. it is obviously "destination 0.0.0.0" "next hop X.X.X.X" we would like to be able to set another static route BUT on source address instead of destination. I have heard other vendors can do this but I am not...

As it happens both 8600 & contivity where on the same power circuits but now we have moved contivity elswhere. We do not seem to have any issues since so hopefully it was a one off . Thanks for all reply,s and advice Mucka

Thanks once again guys , around the same time we had a contivity box crash that connects directly into the passport and it took the hard drive out , coincidence ?? I have since been checking the "show log file tail" for clues but no "malloc errors". are there any checks/tests I can do to...

Yes , thanks for the info the .000 file gave the fol error message at 4am sat morning: error code xxxx can,t malloc pkt memory 32 <np> IP-RIP eroor iprx: out of memory.(Whatever that means!) This repeated umpteen times ,and we do not have rip enabled ! foll this message there was nothing till...

Thanks for the reply Anthonyanderberg my collegue says the utilisation was not unduly high .It was not passing traffic through to servers etc. We use e series on this box. What particular bugs did you experience with 4.0.2.1. ? Thanks again Mucka

Hello Al , any help please we recently had a problem were our main 8600 froze .It is a fully polulated box with many stacks/servers/main frames , and other 8600,s hanging off it.We couldnt telnet or device manage it although we coud ping it , unfortunately my collegue didnt have a console cable...

Thanks for the onfo guys, the answer to the last question is they are feeding 10 other switches (5 each side of a rack enclosure)that then feed blade servers !! Mucka

Hello all , we have 2 passports with IST but instead of having SMLT to 5510 stacks ,our customers want 2 seperate 5510,s one from each passport.This is because of the 6 MLT limit per switch. I have done this with the same vlan on each 5510 and the same gateway HOWEVER it reports a ip conflict on...

Hi guys any help please , on a given lan some citrix clients can pick up dhcp others cannot.Same build on all citrix wyse v90 winterm.If we give a static all is ok.Auto is also not an issue we have forced speed and duplex all combinations. Thanks in anticipation Mucka

General rule of thumb is if they both have the same firmware & isvn number they should be ok but in my experience the second 5510 joining the base may reset to factory default & Vlan 1,so make a note of settings .You will need to change your switch ip address to a stack ip address when teamed...

Hello all , hope you had a good christmas ! bit of advice please , we have two passports connected thro IST on seperate vlan & no OSPF . Would I be correct in having their respective default V1 addresses on the same subnet ? ie: 10.254.254.2 passport A and 10.254.254.3 pasport B./24 mask. This...

hello guys , I wrongly created a role & device association within device setup within policy services ,how can I now delete it ,it doesnt seem to give me the option ,delete is greyed out & a right click only allows a refresh. Any help much appreciated . Thanks Mucka

A further question guys with no routing protocol on IST vlan , do we add the relevant vlans we need to pass thro the IST in the MLT area ?? presumably all vlans needing to communicate thro! IST must also be in ? given that we have no routing protocol on IST. Any help much appreciated Thanks Mucka