Hi,
I have tried to configured Avaya IP Office 500 V2 to Asterisk Elastix PBX.
All PRI Lines are connected to Avaya. Incoming workings on Asterisk Extension as per the DID route created, Outgoing also working fine, but call going through default main number 04444700 when Asterisk Ext User Dial...
Thanks Everybody.
But, Im wanted the report on my Windows 2008 Server, on which I have Avaya IP Office Manager loaded, but it doesnt have hyperterminal.
Thanks for your Reply
1º Check that the services start. - AFTER LOOKING TO BELOW LOGS I FEEL, SERVICE IS RUNNING, I DONT SEE ANY SERVICE IN SERVICES LIST.
2º Check firewall - CHECKED FIREWALL.-DISABLED.
3º Check IP OFFICE config. IP and port of the computer it's running services.-CHECKED ITS...
I tried to setup SMDRSERVICE.EXE by Following Steps.
But Still cannot see the Report Folder Path
Installation Steps Taken.
The service must be installed using ‘installutil’, from an elevated command prompt change to the directory containing “SMDDService.exe” and run...
Thanks for the Information.
How can I get SMDR Output directly my AVAYA 500 Series- Relase 7.0.26 to my PC.
Any solution or setup required.
-Thanks,
Sam.
Hi,
I was trying to setup AVAYA Delta Server 3.0 for my AVAYA IP Office 500, on 7.0.23 Release.
After I setup File Location and Enabled SMDR and select Comms and detected my IP Office & Applied Ok.
I get Comms Status : CommS Failure.
May I have any solution or any upgraded version.
Your...
Dear Mr.Peter,
Thank you Soo Much !!
Its really helped to sort out my problem to use Teleworker Licence.
I have one issue on AVAYA 1408, whenever the user recieve the call by phone speaker, automatically it goes to mute, the recipient cannot hear the and user must have to lift the phone.
Is...
I tried the same process to upgrade from....by open R8 IP Manager and gone to into directory preference change the path to R7 IP Office Manager Location....But when tried to upgrade it shows All Transfer Failed.
I couldnt make it.
Please help me to start using Teleworker licence.
-Thanks,
Sam
Thanks.....
Formatting seems risky.
Instead of I would prefer to go for ...the alternate option...like open IP Office Manager R8 and select the R7 Directory .....will try to downgrade to R7...hope that might work.
-Thanks,
Sam.
Thanks,
Simply Removing SD Card and Formating will work.
Or Else...I need to Install AVAYA IP Office 500 7.0.26 and try to upgrade.
Any alternative solution please.
-Thanks,
Sam.
Dear Friends,
I wanted to know how can I downgrade AVAYA IP Office 500 R8 8.0.8 to R7.
I would like to downgrade due to Activate Teleworker Licence in R7 Version, otherwise I have to go for Preferred Edition Licence just to use AVAYA Teleworker Licence.
I have downloaded 7.0.26 IP office...
Dear Friends,
I wanted to know how can I downgrade AVAYA IP Office 500 R8 8.0.8 to R7.
I would like to downgrade due to Activate Teleworker Licence in R7 Version, otherwise I have to go for Preferred Edition Licence just to use AVAYA Teleworker Licence.
I have downloaded 7.0.26 IP office...
Thanks for your time
Yes, we tried....im getting ping reply when the problem comes.
Then we have restart both end system only then it get sttart the SIP activated for next 12.
Is there any option in SIP TRUNKs, where SIP Trunk get refreshed or reactivated at certain interval of time.
-Thanks...
Dear Customer Care,
I have Panasonic NCP 500 on which I have added SIP Trunks Lines from Gradewall SIP Service provider & also tried to added 3-SIP Extension provided by my Private Tribox IP-PBX System, which is placed in different network.
Now, to connect Tribox Extension, I can connect...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.