Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. tecnouser

    SLC24 and base station issue

    Hi SBCSU, Yes this is a fresh new install, anyway when you said to check the obvious you been definitely Right why: because it turn to be an MDF labeling problem , we been cabling the BS5 in an SLMO position that's why the base station keep reseting, So this is for the next field tshooting...
  2. tecnouser

    SLC24 and base station issue

    Thank you SBCSU, I'm using the CAT 7.0.18, but I will install the latest CATool and let you know. Tecnouser
  3. tecnouser

    SLC24 and base station issue

    Hi all, I have an SLC24 installed in an OS4K V7 R1.39.0, the card in ready in the dis-bcsu and light green but the BS5 don't come up and keep resetting, I already tried a BS4 but noway; same issue. The latest loadware available in SEBA has been loaded, so if anyone have the thinest clue ...
  4. tecnouser

    IP trunking between MXone TSE & Unify UC4000

    Hi, I don't know if this post is still active, so if its still so I can say that the configuration of the Unify looks OK , but can you post the configuration of the MXONE especially the codec priority so that we can check Tecnouser
  5. tecnouser

    Openscape 4000 V7 with Concierge V3

    Dear all, Just for information the ACWin will be phased out this month , the replacement is the existing Concierge which is a solution in the call center portfolio, Unify plan to have the ACwin back in starting form the second half of the next year after finding a replacement for the third...
  6. tecnouser

    licenses

    Hello, If you want to network the two systems between each other then you have to get one networking license for each system and an amount of sip trunk license ( trunk channels ) on each one Cheers Tecnouser
  7. tecnouser

    COS hipath 4K

    Yes this can be a solution as I didnt find class of service to deny the transfert. Thank you Tecnouser
  8. tecnouser

    COS hipath 4K

    Thank you dond01 for your reply , but the needed restriction is to be able to place an outgoing CO call but to not be able to transfert it the internal party, as you said I will have a look in the COSSU:COS and will let you know. Thank you Tecnouser
  9. tecnouser

    COS hipath 4K

    Hello experts, Sometimes you get strange requests which will set you clueless, here one of them that I will be happy to find out how you are managing it: My customer want to give some extension the right to make external CO calls by without being able to transfer them to internal party, By the...
  10. tecnouser

    DHCP and Hipath 4000

    Hello, Yes the DLS is a very good provisioning server ( logo, firmware update, gateway address ...), if this is the only way so we have to cope with it. Thank you tecnouser
  11. tecnouser

    DHCP and Hipath 4000

    Hello Experts, I am new to the HP4K system world so I have a small question which is the following: For HFA phones I would like to use DHCP for Ip configuration ,but the issue is that I have to put the Gateway address manually. Beside using a DLS server is there anyway to setup the DHCP server...
  12. tecnouser

    hipath 4000 dulpex

    Hello Sbcsu, Me too I think that its in the backplane, Regards
  13. tecnouser

    hipath 4000 dulpex

    Hello tek users, After checking every things and every place the issue has been solved by replacing the CSPCI chassis , so you never know what's next :=)) Regards
  14. tecnouser

    hipath 4000 dulpex

    Hello, Yes I have the 2 fans and 1 ACPCI, in the SUSE linux when checking I get: soco2-sys2:~ # checkydata V6_R2.16.1 Version Check OK So I dont know , my be an issue with the R2 , I will get the R1 and see what we will get. Regards
  15. tecnouser

    hipath 4000 dulpex

    Hello , Just in case , even when shutting down the ccb and keeping cca only it keep rebooting with the following in the HISTA: F8272 M4 N0081 LOCK BPA TRANSSYS PARTNER NOT AVAILABLE 14-11-10 16:24:38 ALARM CLASS:CENTRAL:023 PARTNER:BPB IP-ADDR:192.0.2.2...
  16. tecnouser

    hipath 4000 dulpex

    Hello, Yes the RTMs are inserted in the same position in the back as the DSCXL2 in the front, cables between the eth4 and eth6 of the two cpu are connected as well, the RTM activation leads to the same result as the LTU: ACTIVATE-USSU:UNIT=RTM,TYPE=BOARD; H500: AMO USSU STARTED H28: RTM IN...
  17. tecnouser

    hipath 4000 dulpex

    Hello, Here the status; <ACT-USSU:LTG, 1; ACT-USSU:LTG,1; H500: AMO USSU STARTED F29: THE ONLY EXISTING LTG ON ACTIVE PBX MAY NOT BE SWITCHED ON. ACCORDING LTU MAY BE SWITCHED ON BY MEANS OF ACT-USSU:LTG,,<LTU-NR>; AMO-USSU -111...
  18. tecnouser

    hipath 4000 dulpex

    Hello, Unfortunatly not, I can give you the output of the command when i will be in front of the machine. Regards
  19. tecnouser

    hipath 4000 dulpex

    Hello , Please find after the result of the commands: REG-DBC; H500: AMO DBC STARTED EXEC-DBC:"4000 ",6; AMO-DBC -111 DATABASE CONFIGURATION REGENERATE COMPLETED; < And DIS-SIGNL:SYSTEM; H500: AMO SIGNL STARTED...
  20. tecnouser

    hipath 4000 dulpex

    Hello experts, I'm trying to set up a hipath 4000 V6 in test lab, the version has been installed in the two dscxl2, but when I send the ACT-USSU:UNIT=LTG,LTG=1; only cca become active with no ccb standby. Thanks in advance for your help tecnouser

Part and Inventory Search

Back
Top