Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. stokerel

    RCC Report Viewer

    Hi, I also have the same problem on a BCM400 system running the latest version of RCC. Could you please help me with your solution? Many thanks, Radu. my email address is stokerel [at] hotmail [dot] com
  2. stokerel

    CP 4.0 no audio

    I've tried that, with no success. In the mean time, I've discovered that the cause was a bad DSP card on the CallPilot... I've replaced it and now it works fine. Thanks!
  3. stokerel

    CP 4.0 no audio

    Hi guys! I have a CS1k 5.0 system, fully patched and a CallPilot 4.0 also fully patched. My problem is that I get no sound from any CallPilot voice prompts. I tried everything, all default prompts, creating a custom application with custom voicepromts...nothing. Note that I'm using IP phones in...
  4. stokerel

    CallPilot 4.0 no audio

    oops looks like I posted on the wrong section. Please move this to the callpilot forum. Thanks!
  5. stokerel

    CallPilot 4.0 no audio

    Hi guys! I have a CS1k 5.0 system, fully patched and a CallPilot 4.0 also fully patched. My problem is that I get no sound from any CallPilot voice prompts. I tried everything, all default prompts, creating a custom application with custom voicepromts...nothing. Note that I'm using IP phones in...
  6. stokerel

    BCM.R400.SU.System.018-200901

    I tried a cold reboot, but it did nothing. Also, applying the latest core update did nothing. In the end I had to replace the cards; with the new ones, the firmware update was successful after one or two retries (?) but in the end it worked. I have to check if I can restore the firmware on the...
  7. stokerel

    BCM.R400.SU.System.018-200901

    I'm also having issues with this patch: two out of three GATM8 MBMs stopped working with the following error message: AlarmID: 51 Core Telephony - A trunk media bay module has been disconnected. They show up in Telephony Resources as enabled, but no lines appear in Active Physical Lines. I've...
  8. stokerel

    US robotics Modem

    Thanks for the post, Lynx77 it was very helpfull ;) Radu.
  9. stokerel

    Change system from Mu-Law to A-law

    in ld 17 - parm - set PCML to A if you use a PRI card, you must define each channel in ld 14 with PCML set to A as well. Hope this helps, correct me if I'm wrong guys. Radu.
  10. stokerel

    busy tone disconnect time

    Thanks acewarlock for the answer. Unfortunately there is no moderator involved usually, so I need the call to get disconnected automaticly.
  11. stokerel

    busy tone disconnect time

    Hi guys, I have an issue using an ICB Rls4.0 and a PRI line. When the conference is established and one external participant leaves the conference by hanging up the (mobile) phone, all others hear a busy tone for about 30 seconds. The only way around this is to mute that participant using the...
  12. stokerel

    touchtone on IP phone

    I'm experiencing the same issue. I'm not getting any dtmf tones from my ip phones to the local integrated conference bridge. I have set the eest and dtmf to yes in ld 15, ftr_data, but the tones still don't get to the ICB.
  13. stokerel

    CS1000E Rls.5.0 CPPM CS boot problem

    seems there's a bug in the CPPM software blocking either the FMD or RMD boot capability. I tried booting from the faceplate to upload another customer database on the system, and it wouldn't boot from the RMD, although I pressed F to boot from the faceplate. Then I tried formatting the FMD to...
  14. stokerel

    ICB 4.0 problem

    I've managed to solve the issue partially by manually converting all the wav files to a-law. Now the voice prompts are no longer distorted, but I still have a problem that happened before the change. When I try to use a dial-out group, I get this message on the ICB serial port: 0043 DEBUG...
  15. stokerel

    ICB 4.0 problem

    I've noticed something on the reboot: the card is setup to use mu-law. How do I change this to A-Law? I'm in Europe and I have the phones and the PRI set to A-law. I'm browsing through the debug cli menu now, but there is no NTP describing the commands.
  16. stokerel

    ICB 4.0 problem

    yeah, I tried rebooting. Thing is this issue only appears on the ICB. Other calls have perfect voice quality, so it must be something with the card.
  17. stokerel

    ICB 4.0 problem

    I have a cs1000e 5.0 system, new install, with a PRI line and a ICB rls 4 installed. I use IP Phones as extensions. When I dial into the conference bridge, either from the IP phones, or on the PRI line, the voice prompts are very noisy and distorted; the users barely understand what the...
  18. stokerel

    how to change the NORTEL , name display in the phone on the switch

    thanks guys...didn't know that
  19. stokerel

    how to change the NORTEL , name display in the phone on the switch

    on Rls 5.0 it doesn't seem to work in ld 17 at all. It only displays the value: idle_set_display NORTEL and skips it. Any ideas?
  20. stokerel

    CS1000E Rls.5.0 CPPM CS boot problem

    OK, it worked with a 1GB compact flash, fortunately. Seems it's a must to have this capacity FMD. Anyway, after it booted and formatted the FMD, the system again wouldn't boot, it froze after the CPU frequency listing. I had to format the 15MB partition left visible on the FMD with the mkboot...

Part and Inventory Search

Back
Top