Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. TSupportEngineer

    Configurations from version 12.2 may not be correctly under

    Hi All, I have a 2511 and after updating the BootROMs to Version 11.0(10c)XB2, I get the message, "%SYS-4-CONFIG_NEWER: Configurations from version 12.2 may not be correctly understood, and F3: 11943416+616224+825900 at 0x3000060. The router is loaded w/12.2-10b IP Plus. I am assuming...
  2. TSupportEngineer

    Transfer IOS to new router

    Hi all, There is a command "copy flash flash". I beleive this is where one router is being used as the TFTP server, but don't remember for sure. Probably going to look it up and try it tonight between two 2610s.
  3. TSupportEngineer

    Console Baud Speed Does Not Hold

    Thanks, Burt. Something I will remember next time to save a step!
  4. TSupportEngineer

    Console Baud Speed Does Not Hold

    Hi all (again), Well you know when in doubt, try something else. Figuring there must be another way to set console speed w/o going into ROMMON, I did a: config t line con0, then I punted (typed "?") It just so happens there is a "speed" command for the combination receive and...
  5. TSupportEngineer

    Console Baud Speed Does Not Hold

    Hi all, In practicing xmodem on a 2600 router, I changed the console speed to 115000 as was suggested in the Cisco website when running xmodem. I recovered from a deleted IOS, reloaded it, but cannot seem to return the console speed to 9600 from 11500. I get into ROMMON, type confreg...
  6. TSupportEngineer

    Erasing Flash

    Make sure you can ping the TFTP server from the router. Depending on the TFTP server you are using (I was using the old Cicso one) you may want to shut it down and restart it. Worked for me one time.
  7. TSupportEngineer

    Erasing Flash

    Well, looks like I found a solution, have to use bootrx to overlay an IOS. Apparently the new IOS's (12.1??) do this automatically and transparently.
  8. TSupportEngineer

    Erasing Flash

    Hi all, I have successfully repartitioned a 2-partition flash set on a 2500 router to one partition. One flash set was read/write, the other one is a read only and I erased the read/write stick. I am trying to replace the IOS from an IP set to an IP/FW/IPSEC one and need more than an 8 Mb...
  9. TSupportEngineer

    2505 router/hub, hub not working

    Hi All, First, thanks for all your help, it is always appreciated. Got everything working now, after removing and reinstalling the NIC from the workstation configuration. That worked. I started again w/a 2501 and was able to copy the flash imaage to the tftp server (the old Cisco TFTP server...
  10. TSupportEngineer

    2505 router/hub, hub not working

    Something I forgot, tried both straight through and crossover with the hub, still no good and no lights. I will post the version tonight.Thanks.
  11. TSupportEngineer

    2505 router/hub, hub not working

    Burt, CiscoGuy, and Dallas, Thanks for your help. The workstation orginally was connected via console cable to several 2501's. In addition to practice (and backup) IOS transfers, the e0 port of the router(s) was connected to a NIC through a tranceiever and a straight-through cat5 cable. I...
  12. TSupportEngineer

    2505 router/hub, hub not working

    Burt, The router is connected to a workstation via the console cable. It is also connected from one of the router ports to the workstation network card via a crossover cable. I know the crossover is good because I saved IOSs to the TFTP server on the workstation the same night. This is for...
  13. TSupportEngineer

    2505 router/hub, hub not working

    Here's the e0 interface and config: Enterprise10#sho int e0 Ethernet0 is up, line protocol is up , using hub 0 Hardware is Lance, address is 0000.0c47.8bba (bia 0000.0c47.8bba) Internet address is 192.168.14.2, subnet mask is 255.255.255.0 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec...
  14. TSupportEngineer

    2505 router/hub, hub not working

    Hi all, I have a 2505 I had been using in a lab. I had kept it because it has an IOS Enterprise version on it so it has been useful for practice. Haven't used it lately and when I boot it up, the hub light doesn't come on where the ethernet cable is plugged in. I have enabled the ethernet...
  15. TSupportEngineer

    Download for Live Meeting 2005

    Thanks for your help.
  16. TSupportEngineer

    Downloading Live Meeting 2005

    Thanks. This is the same link I have tried before. Looks like I'll have to go to a retail app. But thanks again for trying!
  17. TSupportEngineer

    Downloading Live Meeting 2005

    Thanks Simon, but I tried those files. They do not install completely, stoppoing after the second screen from the install. No program listing or shortcut is made in the start menu/desktop.
  18. TSupportEngineer

    Download for Live Meeting 2005

    I tried to download Microsoft Live Meeting 2005 before 2007 came out which is not free anymore, but looks like I may have lost my chance. Anyone know where the full install is still available? All I can seem to find is plug-ins. Thanks in advance.
  19. TSupportEngineer

    Downloading Live Meeting 2005

    I tried to download Microsoft Live Meeting 2005 before 2007 came out which is not free anymore, but looks like I may have lost my chance. Anyone know where the full install is still available? All I can seem to find is plug-ins. Thanks in advance.
  20. TSupportEngineer

    2511 Bumps Out Connection From Remote Router Back to User Exec Mode

    As always, Burt, thank you VERY much for the quick reponse. The address is ok, I'm using a loopback to configure reverse telnet, I just typed the command incorrectly, but you brought my attention to it. It is for my recertification lab. Hope you had a great long weekend. Again, thank you, sir! Barry

Part and Inventory Search

Back
Top