Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: jabst
  • Order by date
  1. jabst

    What is SPF

    Thanks,
  2. jabst

    What is SPF

    Where can I find this REQ: prt TYPE: dnb CUST 0 DN 1 DATE PAGE DES DN 1 TYPE SFP
  3. jabst

    TTY Port Wont come up

    I'll remove it in the morning and look at it, since the tty's are ctyp are quad sdi I will probably need a new one Thanks,
  4. jabst

    TTY Port Wont come up

    At the back of Core 0 I have J13 J14 & J15, J15 has a label tty01 next to it, My ACD print is on tty 2 which is connected to J14. J13 says Critical I on it. So I assume I dont have a tty 4 to connect to. Does that make sense?
  5. jabst

    TTY Port Wont come up

    How can I tell?
  6. jabst

    TTY Port Wont come up

    tty 4 >ld 37 IOD000 .stat TTY 0 : ENBL TTY 1 : ENBL TTY 2 : ENBL DES: ACDPRTR TTY 3 : ENBL TTY 4 : DSBL DES: CDR TTY 5 : ENBL TTY 6 : DSBL DES: elman1 TTY 7 : DSBL DES: elman2 TTY 8 : ENBL DES: elman3
  7. jabst

    TTY Port Wont come up

    Ok, back in now and here is the ADAN REQ prt TYPE adan ADAN HIST SIZE 20000 USER MTC BUG ADAN TTY 0 CTYP QSDI DNUM 0 DES FLOW NO USER MTC XSM YES TTYLOG 0 BANR YES ADAN TTY 1 CTYP QSDI DNUM 1 DES FLOW NO USER MTC TRF SCH BUG...
  8. jabst

    TTY Port Wont come up

    I lost all access to the system, I can get in through element manger.
  9. jabst

    TTY Port Wont come up

    I built a tty port and when I enl tty x I get IOD006 Must I ini the switch before it will come up? Thanks,
  10. jabst

    4.0 Wont reset to Default

    Yes, Found out the vendor that installed changed from 2/6 split to 3/5 with out a cold reset, I am installing a new hard drive due to the data corruption. Thanks,
  11. jabst

    4.0 Wont reset to Default

    I have a BCM 400 upgraded from 3.7 to 4.0 2 years ago, Company implemented 66 IP phones 6 months ago, I have been plaqued with problems since. 58 phones registered and 48 can 4 digit dial across network, the rest cannot. Delete those phones and reprogram and still cant dial. These 10 in Monitor...
  12. jabst

    LHK ?

    ok, thats the way I programmed it. thanks to everyone for your input!!!!
  13. jabst

    LHK ?

    Ok, I removed key 2 & 3 from the five phones and then added key 2 & 3 with lhk 4 on tn 65 5 and then tested, it worked fine, and the I I did the same for the rest of the phones and tested and is now working fine. Question I have now is when adding the keys I started in the middle of the tn range...
  14. jabst

    LHK ?

    Yes, 5 ext's have 1111 as key 2 and key 3 is 1101,
  15. jabst

    LHK ?

    OK, changed to LHK 4 and I still get a busy while talking to 1xxx and call from my cell, any ideas. Thanks,
  16. jabst

    LHK ?

    Thanks!
  17. jabst

    LHK ?

    I four Keys with a DID on each key, call comes in 1xxx and rings key 2, while on call a new call comes in caller gets busy, DCH msgi shows call presented to 1xxx. How do I change to hunt up to the next key?
  18. jabst

    BCM 50 Power Supply part #

    Does anyone know the NT number for a 50 power supply? P/N 9NA1200312. I can't find it in ay of the docs. Thanks,
  19. jabst

    CLID Coming in on PRI

    That is correct, only the number is displayed. Should msgi also show the cpnd from the CO ?
  20. jabst

    CLID Coming in on PRI

    This is what is coming in DCH 11 UIPE_IMSG CC_SETUP_IND REF 00005C0E CH 1 1 TOD 10:44:04 CK 3B029E82 CALLED #:1184 NUM PLAN: UNKNOWN TON: UNKNOWN PROGRESS: ORIGINATING END IS NOT ISDN CALLING #:7111234567 NUM PLAN: E164 TON: NATL DCH 11 UIPE_IMSG CC_DISC_IND REF 00005C0E CH 1 1...

Part and Inventory Search

Back
Top