Search results for query: *

I have three seperate private network systems, I will call them 10.0.5.1, 10.0.3.1 and 10.0.1.1 255.255.255.248 subnet for all three networks. I am running these to a cisco 2950 and all networks are running on vlan 1 only. I have a cross over cable, one from each network, plugged into the 2950...

I am doing a xmodem -r (file name) and i cant get the ios to show in the flash, im doing a "sh flash" and it says no directories. How the heck do i get the ios to flash so it will boot up? its running with the ios and configs, but like i said its not showing in the flash dir. TIA

Ok heres the details, this one is killing me. I have a 2651 router that i want to load 12.3(t3) ios. I am using xmodem because im in rommon mode and it goes all the way down on the install till the last moment. It says erasing flash, then errors"cannot erase flash", aborting. I have assured...

All: I am looking for the process to reset a cisco 2950 switches secret pwd. I had a process that was from bootloader and then doing flash_init, boot_loader, but i forgot what the rest of the process was. Any help would be great and TIA.

I erased an IOS on a 3750 switch and want to reinstall. I attempt to do various break key sequences and nothing will break. All i get to on the switch is the boot loader commands (IE: version, unset, type, trap) I am using solarwinds for my tftp but again i cant get a break sequence to work...

I want to copy multiple files from my solar winds tftp to my 2600 router, i am unable to do this. I can tftp single files fine, but i have 26 files and it is just time consuming. From the 2600 how would i get all the files from the tftp server? TIA

Could someone explain to me how a 2600 router can route 10.x.x.x IPs and have them be globally significant. I have been told that this can be done without nat or any other hardware. And i should be able to ping that 10.x.x.x network from anywhere on my own network which in this case is a...

People my problem is that I have an old network I am working on and it currently has two vlans on it, vlan 1 and 100, one has a 22. network and the other has a 10. network. I want to remove the 22. network and yet have the 10. network communicate through the current 22. network defualt gateway...

I am trying to change the following gig ports to switchport mode trunk, and I get an error stating that i cant because the port is already in encapsulation AUTO mode. help please, i just want to change them over, and I cant fig out the commands: interface FastEthernet0/23 switchport mode...

I am trying to change the following gig ports to switchport mode trunk, and I get an error stating that i cant because the port is already in AUTO mode. help please, i just want to change them over, and I cant fig out the commands: interface FastEthernet0/23 switchport mode dynamic desirable ...

I have a 3550 cisco switch with 12 gigabit slots. I have this connected to a 2950 with two gigabit slots. I am having trouble turning up the gigabit port with a general "no shut" command. Across this gigabit run, which i lighted and tested good on the fiber, I am running a vlan with a static...

My problem currently is that there is no ios on the 2950 switch i am using. I have the .bin file for the ios that i want to use ready to load on the TFTP server. when the switch comes up it comes up with only a "switch:" I have used the express install, but would like to get the ios installed...

I have a cisco 2950 switch with vers 12.0 (14) IOS. I am attempting to create a user using the following format: user gcoutin priv 15 password 7 pass$word I have tried various methods but i get the error: unable to encrypt pass$word What is causing this? Other user accounts have been...