Search results for query: *

Hi Folks, I have HPs Network Node Manager installed on my network. It is configured to send an report via email to me daily, however I am not receiving these reports. In the queue viewer of our exchange 2007 box I see my reports, which are suspended. Here is the text that comes up, when I...

Hi Everyone, I recently install HP OpenView, network node manager (Start edition). I lefted it to run overnight to discover my LAN. After a few days it has only discovered only 6 nodes on my network. I cannot understand why the other nodes have not be discovered. I am presently researching...

Hi, I am using a evaluation version of the hp openview network node manager. When I try to add a node I am prompted for a username and password. The documentation I have read did not make mention of this. Please asist thanks Adesh

Hi all, I have an Isa 2004 Server with three networks (3 nics) connected to it. There is the external nic for internet connectivity, a nic for a branch network and one for the local internal network. I have defined all these networks and set up the respective firewall and Nat rules for each...

Hi Everyone, I am attempting to install a T1 card on my cisco 2651xm. The following is the error I am getting: "TTTLCCME(config)#controller t1 ^ % Invalid input detected at '^' marker." The IOS I am running is : IOS (tm) C2600 Software (C2600-IPVOICE-M), Version...

Hi Everyone, I present I am reviewing some security concerns with one of my terminal services servers. I know the tslinternetuser account is needed by terminal services. How do I properly secure this account. Can I disable it? Give it a strong password? The following article got me concerned...

Hi Everyone, Is it possible to collect Call Manager Express call history logs using a syslog server. At present I have syslog logging enabled on my CCME router and pointed to the IP address of my syslog server. However I only get logs of events from the IOS, not the CCME. Adesh

Hi Everyone, I would like to know the proper way to remove a child domain from a forest. I think I know what I need to do which is just demote the child DC. This should remove the child domain aswell as the parent- child trust relationship. Is there more to this? Please Advise Thanks Adesh

Hi Everyone, I recently acquired a used router, I need to setup a console and telnet username and password for this router. When I telnet into the router it prompts me for a password. I would like to have both a username and password prompt. Thus I did the following R1#configure terminal...

Hi Everyone, I have a parent - child domain structure. I am trying to resolve a dns name in my child domain via pinging, but I am getting the following error "ping request could not find host". I know this must be a dns issue because I can ping the IP address of the machine. Went I go to ->...

Hi Everyone, I'm attempting to create an user account in an specific OU in my Active Directory, however no mailbox is being created for this account. I initially thought the problem was with the Recipent Update Service and followed the instructions on the link below to correct the problem...

Hi everyone, I am trying to restore an exchange mailbox from my backup tape. However the restore fails. In the activity log the following error is displayed - 8601 failed to connect to agent I am using Brightstor Arcserve Backup r11.1 I know my backup agent RPC service is running because I...

Hi Everyone, I have been asked to monitor the bandwidth and protocols that are passing through my 2600 router. I am using Passler router traffic grapher sofware to generate my graphs. I have never configured netflow on a router before, however after reading some cisco documents this is what I...

Hi Everyone, I plan to enabled snmp on my cisco 2600 router using the following command: Rtr(config)# snmp-server community public RO Rtr(config)# snmp-server community private RW Is that all it is to securely enable snmp on my router? Are there other procedures that need to be followed...

Hi, I got an catalyst 3550 series switch. I'm trying to figure out how to change the username. I have a link here that tell you how to reset the password www.cisco.com/warp/public/474/pswdrec_2900xl.html But it does not indicate how to reset the username. Does anyone know the command to...

Hi, I recently acquired a cisco 2600 router, when I attempt to access the router via the console port the logon screen comes up prompting for the username and password. I don't know the username nor the password. I found this link with a really good password recovery procedure...

Hi, I am presently using Sharepoint Team Services as our company intranet solution. ASP is used to publish documents to the intranet. A typical intranet url is http://servername/applications/revenues.asp How can I shorten this url to something look http://servername/revenues.asp Adesh

Hi, I am presently using Sharepoint Team Services as our company intranet solution. By default the intranet virtual server takes the form http://servername. Is there a way to mask or rename this url? Adesh

Hi Guys, The usb ports of PCs on my network are being disabled. It has happen twice in the last two weeks. I am basically clueless as to why this is happening. I have gone through my group policies with a fine teeth comb. I have also disabled my WSUS server. Since disabling the WSUS server the...

Hi Everyone, I deleted a user from AD. When I look at my mailstore, I see the deleted user mailbox has a red 'x' on it. When I try to purge the mailbox, I get an Error message: (c1038af9) "The operation cannot be performed because the mailbox was already reconnected to another existing...