Search results for query: *

Hi All - perhaps you can help? We have an existing CME SCCP on 2811 running 7960's/7970's. We use incoming SIP trunks to ephone-dn's and overlay these to multiple phones (so multiple users can see the incoming line ring). All fine. Now adding a couple of SIP clients, most notably iPhones...

All, Our 2811 is running CME (SCCP) successfully with many 7960s/7970s, and we now have a remote office online via a router-router VPN. CME is 10.0.0.1 and remote office is 10.0.1.x. How do I get remote 7960's at 10.0.1.x to come up on CME at 10.0.0.1. As the MAC address is used by CME, I seem...

All, Currently have a mixed SCCP/SIP CME implementation. Looking to have incoming Skype calls as a ephone-dn (so I can map it to a number of handsets), and outbound Skype calls (via a dialling prefix). Aim is to provide a free-Skype dial-in number of international callers. Has anyone...

Everyone, We're currently working up an Asterisk vmail config - but have hit a (seemingly trivial snag). Perhaps you can help? We use Shared Lines extensively, such that a single user can see multiple POTS and SIP incoming lines. For this reason, configuring a single Voicemail pilot number at...

Hi Everyone, Have CCME4 on a 2811 working just fine using SCCP, but need voicemail. Have Asterisk, which my colleague can configure, but cannot find any published configs for the Cisco end of things (have seen lots for asterisk though). Does anyone have such a config they could post - I think...

Hi everyone, I'm trying to get together a baseline config to VPN multiple 2811's into a central 2811. Tried SDM, but it seemed to insert way too much unnecessary stuff. Does anyone have the core lines for the remote sites and the cores for say just pre-shared key, with user authentication on...

Hi Everyone, Just put a VIC-2FXS into my 2811 to support and analogue phone, and it's not shown under sh ver. sh diag yields: WIC Slot 3: FXS Voice daughter card (2 port) WIC module not supported/disabled in this slot Hardware revision 1.1 Board revision A0 Can anyone hint how I might enable...

Friends, We have a site with a 2811 running CME, and 16 7960's around the place. Our office has an intercom at the entry gate, which has a dedicated handset in the foyer. Has anyone found a way of connecting this intercom handset into a Cisco FXS port, so that when a caller presses the ringer...

Hi, Our WinSvr2003/Exchange server is sitting in a comms room with hyper terminal sessions open to environmental monitoring, UPS monitors etc. Each time a message (ie. any characters terminated by a CR/LF), we'd like to automatically email them to our on-call person (who's got direct push email...

All, We run an Exchange server behind our Cisco - all works good, secure and correct - except for one outfit called SORBS - a SPAM database used by some very big companies indeed. We can't get emails thru to people that use them. We've a fixed IP, which is correctly rDNS'd, and have submitted...

Hi, We have a fixed IP from our IP, and four static IP addresses (so our subnet mask is 255.255.255.252). Does anyone know how we configure our Cisco 2811 so that outbound traffic from a specific internal private address could be made so as to originate from one of our four IP addresses...

Hi, Our problem is location - we can only get regular contended ADSL lines (ie. 2Mbps / 256Kbps) - so we have a bandwidth problem. We make extensive use of CME4/Asterisk, but this all falls apart when our Exchange/Web servers and users load the WAN. We have a 2811 with one ADSL-WIC, and we...

It appears that RPC over HTTP is only supported when using physically distinct Front End and Back End servers. For a small company, we would prefer to have just a single exchange server, and not have to upgrade to a multiple server architecture just to support this. Is there any way we can get...